Used Extruders

Pre-Owned Killion KL-075 Single Screw Extruder – Electrically Heated, Air-Cooled
- used
- Manufacturer: KillionKillion
54037006 Used Killion KL-075 Single Screw Extruder. 19.1 mm Diameter screws. 25:1 L/D. Screw speed 12-120 RPM via a gearbox by a 1.1 kW-380 volt/50cycle/3Ph DC motor. 3 housing sections. Electrically heated, air ...
Belvidere, IL
Gloucester 25225R2 Single Screw Extruder – 2.5" Dia., 32:1 L/D, 60 HP Motor
- used
- Manufacturer: GloucesterGloucester
10755152 Used Gloucester Single Screw Extruder, Model 25225R2. 2.5' Diameter Screw, 32:1 L/D. Has an electrically heated, air cooled, and non-vented barrel at approximately a 65? center line height. Barrel is se...
Belvidere, IL
Gloucester 3.5" Single Screw Extruder – Model 35250R2, 32:1 L/D, 100 HP Motor
- used
- Manufacturer: GloucesterGloucester
10755150 Used Gloucester 3.5" Single Screw Extruder, Model 35250R2. 3.5" diameter screw, 32:1 L/D. Having an electrically heated, air cooled, and non-vented barrel at approximately a 65" center line height. Barre...
Belvidere, IL
1998 Milacron Apex 6.0 Extruder
- used
- Manufacturer: Milacron
65" X 24" Cinn/HPM w/6" Ext. 65" X 24" No wind or shear 1998 Used 65" wide Cincinnati Milacron/ HPM 1998 sheet extrusion line last used on PET at Approx 1500-1800 Lbs/Hr. Includes the following: 6" HPM extruder 3...
Valley Cottage, NY
Trusted Seller
1995 HPM TMIII
- used
- Manufacturer: HPM
- Model: TMIII
Used 4.5” HPM Single Screw Extruder 30/1 L/D Model: TMIII Year: 1995 6" x 6" top center feed throat Driven by a 250 hp DC motor, 460 volt AC input and a Powertec motor control with 460 volt 50/60 Hz AC input. Gea...
Hainesport, NJ
Comac EBC 40HT/37D Twin Screw Extruder – 600 RPM, 550 LBS/HR
- used
- Manufacturer: Comac
52622001 Used Comac Twin Screw Extruder, Type EBC 40HT/37D. 40 mm, 37:1 L/D. Production capacity 330-550 lbs/hr. (150-250 Kg/hr.). Maximum screw speed 600 RPM via a gearbox by 51 Kw AC Exp. motor. 7 housing secti...
Belvidere, IL
Trusted Seller
Royle 3.5"
- used
- Manufacturer: Royle
Used 3.5” Royale Plastic Single-Screw Extruder Right angle reducer to a 60 hp Louis Allis type CLC Eddie Current clutch
Hainesport, NJ
Davis Standard 9" Extruder, Model 80IN80HT – 32:1 L/D, 900 HP Motor, Built 2001
- used
- Manufacturer: Davis-Standard
10755163 Used Davis Standard 9" Extruder, Model 80IN80HT. 32:1 L/D ratio; (7) zone electrically heated, water cooled (closed loop), and vented barrel at a 44" center-line; 10.15:1 Gearbox reduction ratio; Gearbox...
Belvidere, IL
Trusted Seller
WENGER X-155
- used
- Manufacturer: Wenger
Used Wenger model X-155 extruder. (1) screw feeder with steam injection; (1) screw feeder with motor, no drive; (1) single-shaft pre-conditioner, cut-off knife. No control panel.
Hainesport, NJ
APV Baker Perkins MP50/25D Twin Screw Extruder – 330 LBS/HR Capacity
- used
- Manufacturer: Baker Perkins
51164005 Used APV Baker Perkins Twin Screw Extruder, type MP50/25D. 50 mm dia. twin screws. 25:1 L/D. Co-rotating. Electrically heated, water cooled. Max Screw speed 500 RPM via a gearbox by a 55.2 KW (74hp)-3/50...
Belvidere, IL
Trusted Seller
Gloucester 60mm
- used
- Manufacturer: Gloucester
Used 2.36” (60mm) Gloucester 32/1 L/D vented single screw Extruder. Year 1986. Driven by a 50 hp DC motor and SCR control. Gearbox 9.48:1 ratio, serial 140. Barrel has 45” centerline height. Includes temperature ...
Hainesport, NJ
Trusted Seller
CREUSOT LOIRE BC-45
- used
- Manufacturer: Loire
Used Creusot Loire (Clextral) model BC-45 twin screw extruder. Machine #750, Serial #5100750. 2 zones, 55 mm diameter screws. 45mm between shaft centers. Includes central console, pneumatic knife, powder feeder, ...
Hainesport, NJ
Trusted Seller
1994 HPM 3.5TMC-24
- used
- Manufacturer: HPM
Used 3.5" 24/1 L/D HPM non-vented extruder. Model 3.5TMC-24, serial #93182. New 1994. Has electrically heated, air-cooled, barrel. Belt driven by a 75 hp brushless DC motor with controls. Flender gearbox type SZN...
Hainesport, NJ
Trusted Seller
Wayne 1.25"
- used
- Manufacturer: Wayne
Used 1.25” Wayne Single-Screw Extruder Driven by a 7.5 hp DC motor with SCR control,230 volt
Hainesport, NJ
Trusted Seller
DAVIS STANDARD 150INDS-20
- used
- Manufacturer: Davis-Standard
Used 1.5” Davis Standard Vented Single-Screw Extruder Model: 150IN DS-20 Driven by a nontagged motor and a Reliance model GV3000 AC drive Gearbox: 6.53:1 ratio, rated for 50 hp, 1.25 service factor, 152 rpm screw...
Hainesport, NJ