Used Extruders

Italtech Sandore Pasta Mixer Extruder – Model MX180DH | 200 kg/hr | 195mm Die | 8.5 kW | Built 2008
- Manufacturer: SandoreSandore
53530001 Used Italtech Sandore Pasta Mixer Extruder, Model MX180DH. 200 Kg/hour extrusion production; 30 kg extruder basin dough capacity; 50/kg mixer/kneader basin dough capacity; 195mm die dimension; Vacon X-Se...
Belvidere, IL
Trusted Seller
DAVIS STANDARD 150INDS-20
- Manufacturer: Davis-Standard
Used 1.5” Davis Standard Vented Single-Screw Extruder Model: 150IN DS-20 Driven by a nontagged motor and a Reliance model GV3000 AC drive Gearbox: 6.53:1 ratio, rated for 50 hp, 1.25 service factor, 152 rpm screw...
Hainesport, NJ
Trusted Seller
DAVIS STANDARD 4.5"
- Manufacturer: Davis-Standard
Used 4.5" Davis Standard 30/1 L/D Extruder, Electrically Heated Air Cooled Barrel. Includes gearbox with 17.36/1 gear ratio rated at 321 hp. Serial #M3316, SO #05432. New 10/1991. Includes Kryenborg Type K-SWE-12...
Hainesport, NJ
Trusted Seller
1991 DAVIS STANDARD 4.5"
- Manufacturer: Davis-Standard
Used 4.5" Davis Standard 30/1 L/D Extruder, Electrically Heated Air Cooled Barrel. Includes gearbox with 17.36/1 gear ratio rated at 321 hp. Serial #M-3315, SO #05432. New 10/1991. Includes Kryenborg Type K-SWE-1...
Hainesport, NJ
Trusted Seller
2000 DAVIS STANDARD 5.11"
- Manufacturer: Davis-Standard
Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...
Hainesport, NJ
Trusted Seller
1997 DAVIS STANDARD 5.11"
- Manufacturer: Davis-Standard
Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...
Hainesport, NJ
Trusted Seller
DAVIS STANDARD 1.5"
- Manufacturer: Davis-Standard
- Model: 15
Used 1.5" Davis Standard 28/1 L/D Non-Vented Air Cooled Extruder. New in 1989. Equipped with 6.53/1 gearbox ratio. Gearbox is belt driven through a 15 hp DC motor. Includes temperature control panel with motor dr...
Hainesport, NJ
Trusted Seller
WENGER X-155
- Manufacturer: Wenger
Used Wenger model X-155 extruder. (1) screw feeder with steam injection; (1) screw feeder with motor, no drive; (1) single-shaft pre-conditioner, cut-off knife. No control panel.
Hainesport, NJ
High-Capacity Prealpina Single Screw Extruder – 1100 lbs/hr Production Rate
- Manufacturer: Prealpina
53309001 Used Prealpina 130 mm Diameter Single Screw Extruder, with a capacity of 1100 LBS/500 Kgs./hr. Electrically heated, air cooled. incl. die head and control panel. Reported to have new screw and barrel. Pr...
Belvidere, IL
Trusted Seller
Gloucester 60mm
- Manufacturer: Gloucester
Used 2.36” (60mm) Gloucester 32/1 L/D vented single screw Extruder. Year 1986. Driven by a 50 hp DC motor and SCR control. Gearbox 9.48:1 ratio, serial 140. Barrel has 45” centerline height. Includes temperature ...
Hainesport, NJ
Leistritz Micro18-GGL Twin Screw Pelletizing Line – Industrial Polymer Extruder
- Manufacturer: Leistritz
40425043 Used Leistritz Twin Screw Pelletizing Line, Model Micro18-GGL. 18 mm Screws, counter rotating screws, 40:1 1/d, 500 rpm screw speed, electrically heated, water cooled barrel, 2.3 kw, 210/260 volt, 2950 r...
Belvidere, IL
Trusted Seller
1994 HPM 3.5TMC-24
- Manufacturer: HPM
Used 3.5" 24/1 L/D HPM non-vented extruder. Model 3.5TMC-24, serial #93182. New 1994. Has electrically heated, air-cooled, barrel. Belt driven by a 75 hp brushless DC motor with controls. Flender gearbox type SZN...
Hainesport, NJ
Trusted Seller
BATTENFELD GLOUCESTER 54" Wide
- Manufacturer: Battenfeld
Used 54" Wide Battenfeld Gloucester Co-Extrusion Sheet Extrusion Line, previously used for approximately 1200 lbs. per hour polypropylene sheet. Line consists of the following: (3) Acrison volumetric feeders with...
Hainesport, NJ
Winkworth ZX500-6 Z-Blade Mixer-Extruder | 500L Working | Vacuum Lid | Jacketed | 304 SS | With Tool Temp Units
- Manufacturer: WinkworthWinkworth
10151559 Used Winkworth ZX500-6 Z-Blade Mixer/Extruder | 500L Working | Vacuum Lid | Jacketed | 304 SS | With Tool Temp Units. 500 liter (132Gal) working capacity with a 778 liter total capacity (product dependen...
Belvidere, IL
Theysohn 45mm Co-Rotating Twin Screw Extruder TSK-N 045 – 500 RPM, 50 HP Gearbox, Side Feeder
- Manufacturer: TheysohnTheysohn
53958001 Used Theysohn 45mm Co-Rotating Twin Screw Extruder, Type TSK-N 045. 45mm (1.77") diameter; 36:1 L/D; 8 housing sections and 1 die zone; electrically heated, water cooled. Max screw speed 500 RPM via a 50...
Belvidere, IL