Used Materials Testing in Taiwan

GR-D01 Vice Action Grip - Rubber Face

• Manufacturer: cometech testing machines

Capacity: 2kN | Jaw face width: (W)mm | Specimen thickness: 0.2~4mm | Mini. load cell: 200N | Temperature limits: -10~200℃ | Weight: 1600g | Jaw face type: Rubber Face

Vicat Heat Deflection Tester Confirm to ASTM D648 ISO 75-1 Standard

• Manufacturer: cometech testing machines

The specimen is given a fixed 10N force (or 50N) at the center with a standard Ø1 mm pin, and the temperature should increase by 50 (or 120) degrees Celsius per hour. When the penetration depth of specimen reache...

Manual Molding Machine

• Manufacturer: cometech testing machines

QC-601B has parallel pressure plates and according to area of the material and force demand to choose machine type. Commonly used in powder compact, parts assembly, lamination work. Put the ingredients in the mid...

Circular Sample Cutter Confirm to ISO3801, ASTM D3776, GB/T4669, BS2471 Standard

• Manufacturer: cometech testing machines

QC-PS can cut specimens of area 100cm², weighing specimen unit weight, the balance of the required minimum reading value should reach 0.01 g. The cutter can cut specimens that thickness are 5 mm. Cutting material...

Electronic Crock meter Confirm to JIS-L0849, ISO-105, AATCC-8 ,JIS-L0862 Standard

• Manufacturer: cometech testing machines

To conduct the test, clamp specimen on fixed seat of abrasion, wrap 5cm x5cm white cloth on the rub-hammer above the specimen, abrasion hammer diameter is 16mm, center load is 900g, abrasion distance is 10cm, wit...

Pneumatic Specimen Punch

• Manufacturer: cometech testing machines

QC-603A of power is pneumatic with hand safety switch design, so there will be no security problem in operation. The tester with all kind of cutter can quickly cut out various shapes of specimen. It is suitable f...

Manual Crock Meter Confirm to JIS-L0849, ISO-105, AATCC-8 ,JIS-L0862 Standard

• Manufacturer: cometech testing machines

This tester’s abrasion head can clamp dry or wet white cloth, under 900g loads, revolving handle by hand to proceed with specimen abrasion test (Common standard is 10 test times), test speed is around 60 CPM. Aft...

Coefficient of Friction Tester, Motor Coefficient of Friction Tester Confirm to TAPPI T-815, ASTM D202 Standard

• Manufacturer: cometech testing machines

QC-117 & QC-117A Put specimen on the platform, and then put dead weight on the top of specimen according to standard requirement. Let platform angle goes up until the deadweight slides down. Get the tan value fro...

Dropping Impact Tester Confirm to JIS-A5403, K6745 Standard

• Manufacturer: cometech testing machines

The specimen is placed on the platform of machine. Choose a designated size of steel ball to fall freely from a height, then the steel ball will impact on specimen’s surface. To observe the specimen of damaged co...

Dyeing Rubbing Tester Confirm to JIS-L0801/L0849/L1006/ L1084/ K6328/P8136 Standard

• Manufacturer: cometech testing machines

QC-319 for textile, leather and fluff dyeing fastness test equipment. Test hammer surface can clamp dry or wet by organic solvent white cloth, abrasion head select 200g or 500g load, speed 30CPM to proceed with b...

Portable Pencil Hardness Tester Confirm to ASTM D3363, ECCA T4, MILC27 227, NEW5350, SIS184187, SNV37113, JIS-C3003/D0202 Standard

GI-M010 according to WolffWilborn standard, this tester is designed to measure the coating surface hardness scrape-resistance, applied to experiment analysis or control production quality, suitable products inclu...

QC-622H Surface Hardness Abrasion Tester

Surface Hardness Abrasion Tester is for measuring surface treatment such as painting, plating, coating, dyeing and finishing the design of the machine. It can use cotton, sand paper, steel wool and eraser to test...

QC-113A Pneumatic Type Drop Tester Confirm to ASTM 5276 / GB/T 4857.5 / CNS 2999 / ISTA 1A / ISTA 2A Standard

• Manufacturer: cometech testing machines

Suitable for testing the impact resistance of packaging and electronic products during transportation. It features a single-wing structure, occupies a small space, and is typically used to simulate product impact...

Spray Tester Confirm to JIS- L1092 , BS EN 24920 , AATCC-22 , ISO 4920, ASTM D1913-2000, ASTM D583-54 Standard

• Manufacturer: cometech testing machines

QC-305 may test water-proof or non-water-proof textile surface water resistance. Clamping textile with 45 degree angle on grip, hold open around 150mm diameter plane, putting sprayer above sample center 150mm, sp...

Portable Hydrostatic Head Tester

• Manufacturer: cometech testing machines

QC-317M(N) Portable design and without electricity that can proceed with test. No time and space limitations, mainly used on the spot measurement, inspect textile water-resistance ability. The test method is divi...