Building Filters
W 1824SD
Touchscreen and length encoder. Miter cut 0 to 45° (R). Hydraulic blade tension. Screw pressure regulator. Vertical presses for cutting bundles. Variable blade speed via inverter. Band saw chip clearing motor. Ch...
Santiago, Mexico
KTM 3VSF
Motor power: 3 HP, 50 Hz, 4500 rpm, variable speed with frequency inverter. 9" x 49" hardened and ground table. T-slots. Precision hardened and ground spindles with double nuts for wear compensation. Precision mi...
Santiago, Mexico
JHU 35100H/NC
Nitride hardened, super finished power. Variable speed workhead rotates 90° CCW and 30° CW. Rapid feed and retraction of the wheel head allows for faster setup and verification of grinding dimensions. Hydraulical...
Santiago, Mexico
SSM 1340BV
Motor power 3HP. Infinitely variable speed range with RPM display in Hi/Low speed range. 1 phase or 3 phase. Push button for easy speed control. Hardened and ground gears and bedplates. Solid bedplate on the enti...
Santiago, Mexico
KLS 1860V
7.5 HP main shaft motor, 2-speed with infinitely variable speed. D1-8 Camlock, 3.2" shaft bore. Hardened and ground gears and bed runners. Jog button, multi-position feed stops. Inch dials and lead screws. Centra...
Santiago, Mexico
KUM 2500 UM
Horizontal spindle motor: 10 HP, 12 speed (40 ~ 1800 RPM). Hardened and ground 13.7" x 72.8" table. Hardened and ground square guides. Table rotates 45° clockwise/counterclockwise. Meehanite GC-45/DIN-40 cast bod...
Santiago, Mexico
KTM 3VKF
Motor power: 3 HP, 50 ± 4500 RPM, variable speed via a frequency inverter, allowing us to go from 0 to maximum revolutions in 3 seconds. 10 x 50 hardened and ground table. T-slots. Precision hardened and ground s...
Santiago, Mexico
KTM 4VKF-E
Motor power: 3 HP, 50 → 4500 RPM, variable speed with frequency inverter. Digital display for real-time RPM reading and spindle load indicator with a green, yellow, and red bar so the operator knows how much load...
Santiago, Mexico
KTM 5VKF-E
Motor power: 5 HP, 50 Hz, 4500 RPM, variable speed with frequency inverter. Digital display for real-time RPM reading and spindle load indicator with a green, yellow, and red bar so the operator knows how much lo...
Santiago, Mexico
JY VH780
10 HP motor, infinitely variable speeds. NT-50 spindle taper. 27.6″ x 102.4″ hardened and ground table. Base and apron with hardened and ground square guides. Precision ACME screws on the X, Y, and Z axes. X, Y, ...
Santiago, Mexico
KTM 3VSF MILL POWER G2 (2-axle / 3-axle)
3 HP motor with variable frequency inverter. Spindle RPM: 60-550-4500. Centralized lubrication via check valves. The guide surfaces are hardened and ground (Rockwell hardness C52). Very easy-to-use conversational...
Santiago, Mexico
KTM 3VKF MILL POWER G2 (2-axle / 3-axle)
3 HP motor with AC variable frequency inverter, features a digital display for RPM reading and an analog load reader. Single-phase or three-phase without the need for a phase converter. 60-550-4500 RPM on the spi...
Santiago, Mexico
KTM 5VKF-E MILL POWER G2 (2 axles / 3 axles)
It features a 5 HP motor with a variable frequency AC inverter. It also features a digital display for RPM readings and an analog load indicator. 60-550-4500 RPM (Hi/Low) on the spindle. 12" x 50" hardened and gr...
Santiago, Mexico
KTM 4VKF-E MILL POWER G2 (2 axles / 3 axles)
It features a 3 HP motor with a variable frequency AC inverter. It also features a digital display for RPM readings and an analog load cell. 12 x 50 hardened and ground table. 60-550-4500 RPM (Hi/Low) on the spin...
Santiago, MexicoKTM 2VH JY
5 HP motor, 9 speeds. 5 HP vertical spindle motor, 12" x 51" hardened table. Y & Z axes with hardened and ground square guides. Precision ball screws on the X and Y axes. X & Y axes driven by an AC servo motor. P...
Santiago, Mexico
