Used die machine

KAWAGUCHI K180-B Die Height Adjustable Tie Bar Nut USED

• Manufacturer: Kawaguchi

Removed from: 180 Ton Kawaguchi Injection Molding Machine Model: K180-B Serial: IE-YY3245 Buyers are welcome to inspect equipment prior to purchase. Expedited shipping services are available upon request. T...

CHAR-LYNN EATON 101 2169 009 Die Height Adjustable Motor Used

• Manufacturer: Eaton

101 2169 009 1 5/8 INCH SHAFT 28.4 MM SHAFT Removed from: 300 Ton Van Dorn Injection Molding Machine Model: 300-RS-30F HT Serial: 2515 Expedited shipping services are available upon request. All taxes due...

CHAR-LYNN EATON 101 2169 009 Die Height Adjustable Motor USED

• Manufacturer: Eaton

1 5/8" Shaft Length 27.9 mm Shaft Diameter Removed from: 300 Ton Van Dorn Injection Molding Machine Model: 300-RS-30F HT Serial: 2515 Expedited shipping services are available upon request. All taxes due a...

CHAR LYNN 101 1032 007 Die Height Hydraulic Motor USED

• Manufacturer: CHAR LYNN

Shaft Diameter: 25.40 mm Shaft Length: 1 3/4" Removed from: 150 Ton Van Dorn Injection Molding Machine Model: 150RS-8F Buyers are welcome to inspect equipment prior to purchase. Expedited shipping services ...

ENGEL ES 330/85 Die Height Adjustable Tie Bar Nut Used

• Manufacturer: Engel

Inside Diameter Approx.: 57 mm Removed from: 85 Ton Engel Injection Molding Machine Model: ES 330/85 Serial: 5965-085-93 Buyers are welcome to inspect equipment prior to purchase. Expedited shipping service...

SUMITOMO EATON SBE07A 2L-B Die Height Motor Used

• Manufacturer: Eaton

Removed from: Sumitomo Injection Molding Machine Model: SH100-NIV A Serial: MOBH0321 Expedited shipping services are available upon request. All taxes due are the responsibility of purchaser. Visitors are we...

DANFOSS OMS 125 151F0502 3 Die Height Motor USED

• Manufacturer: Danfoss

OMS 125 Removed from: 90 Ton Van Dorn Demag Injection Molding Machine Model: Ergotech Cadence 90/16.54-430 Serial: 7158-0004 Expedited shipping services are available upon request. All taxes due are the res...

Hydraulic 5 Ton Press 8" Stroke Punch Die 10Hp 230/460V 3Ph Vickers Pump

• Manufacturer: Vickers

Used, in Good Working Condition, Tested OK. 8" stroke. This is the max. Setup with limit switch. 4" bore Hand levers to operate. Working area is 42" wide and 16" deep. Unit stands 85" tall. Pressure gauge goes to...

30,000 ton Special Build Push Down Type Hydraulic Closed Die Forging Press - Re:24880

• Manufacturer: Special Build

Still installed and under power Force: 30,000 tonnes | Hyds: Water | Stroke: 2,000 mm | Daylight: 4,800 mm | Bed l-r: 3,750 mm | Bed f-b: 2,400 mm | Press action: Push Down | Number of columns: Four | Number of m...

3,000 ton Lake Erie Oil Hydraulic Down Acting Closed Die Forging Press Re:23610

• Manufacturer: Erie Press Systems

This press has been Well-Maintained and is in very good working condition. It is equipped with (2) Model DH 15025 Oilgear 108GPM Hydraulic Pumps, one 150hp motor and one 40hp motor. Available for immediate inspec...

HPM 3.5" Extruder 150 HP 30:1 L/D Strand Die

• Manufacturer: HPM

“Used In working Condition” HPM 3.5" Single Screw Extruder 30:1 L/D Gearbox Ratio 13.881:1 150 HP AC Motor Allen Bradley Drive Control Cabinet Mounted Directly to Machine 20 Hole Strand die Included Screw and bar...

Pneumatic Air 4 Ton Punch Press 1.5" Stroke 12x10" Die Mead Fabco Cylinder

Custom punch press. 1.5" stroke. Made for a 12x10" die. Current die cuts 1-3/4x7/8" holes in flat stock or angle 3-1/4" apart. Has a Mead anti tiedown control valve. Fabco air cylinder. 5" bore 4 stage. MP5X1-1/2...

1970 250 ton Hatebur AMP-30 3-Die, 120ppm,

Dia: 40 mm | Tons: 250 tonnes | Builder: Hatebur | Part dia: 64 mm | Max cutoff length: 72 mm | Max die ejector: 70 mm | Min cutoff length: 19 mm | Max outer dia for combination parts: 55 mm | Max width across t...