- Trusted Seller
1997 BMV T1/250/22-11/150-300/380 48337
- Manufacturer: BMV
Object: 48337 | Drive system: eccentric / crank | Number of suspensions: 2 | Number of slide actions: 1 | Slide ejectors / cushion: yes | Table cushion: yes | Feedstock transport direction: left to right | Total...
Niederhelfenschwil, Switzerland - Trusted Seller
1996 PLATARG 2513 46301
- Manufacturer: PLATARG
Can be tested in operation Max. Flywheel speed: 760 1/min. Capacity on one stage approx. 25T Clutch engagement max. 10/min Air pressure 5.5 bar (min) - 5.8 bar (max) Total deceleration time Braking <250 ms Zig...
Niederhelfenschwil, Switzerland - Trusted Seller
1977 PLATARG 611 43685
- Manufacturer: PLATARG
A new electrical control system and a mechanical and lubrication rebuild are required. One used PLATARG model 611 transfer press, high speed type. Full follow cams. Number of stations: 12 Number of rams: 11 + 1 s...
Niederhelfenschwil, Switzerland - Trusted Seller
1969 PLATARG 312 40583
- Manufacturer: PLATARG
This machine can have the following installed/added to it (not included) o new lubrication o new electrical installation o new protections o CE conformity Number of station 13 (12+1). Capacity on any one station ...
Niederhelfenschwil, Switzerland - Trusted Seller
2000 BENELLI 650T/3MR/2/12/3750X1100/LD/ET3 48090
- Manufacturer: Benelli
Press equipped with 2 feeing lines - one from the side for blank cutting in transfer mode and one in line for for progressive die operation.
Niederhelfenschwil, Switzerland - Trusted Seller
2005 ARKU RM 50X/9 ECOPLAN 43890
- Manufacturer: Arku
Coil line consisting of: - Coil loading chair HUBTEX - ARKU single-sided decoiler - ARKU RM 5050/9 feed straightening machine, +- 0.1 mm feeding precision - measuring wheel to verify feed length - Cut-to-length s...
Niederhelfenschwil, Switzerland - Trusted Seller
LASA LR6-200DL 48420
- Manufacturer: Lasa
Object: 48420 | Feed velocity max.: 18 m/min | Sheet width max.: 153 mm | Coil weight max.: 0.5 to | Max. diameter of coil: 1000 mm | Sheet thickness max.: 1.5 mm | Number of leveller rolls: 7 | Total power...
Niederhelfenschwil, Switzerland - Trusted Seller
1989 ARKU RM 5035.4/21 42744
- Manufacturer: Arku
Line consisting of + Uncoiler ARKU AH4000/MSG-4Q + insert attachment ARKU + precision leveller ARKU RM 5035 4/21 + band loop ARKU levelling capacity according to diagram
Niederhelfenschwil, Switzerland - Trusted Seller
2005 ARKU RM 50X/9 ECOPLAN 46236
- Manufacturer: Arku
Cut-To-Length line consisting of: - Coil loading chair HUBTEX - ARKU single-sided decoiler - ARKU VRM 5050/9 feed straightening machine, +- 0.1 mm feeding precision - measuring wheel to verify feed length - Cut-t...
Niederhelfenschwil, Switzerland - Trusted Seller
SCHULER PDR 250-500 43587
- Manufacturer: Schuler
- Model: PDR 250-500
Object: 43587 | Last overhaul: 2002 | Drive system: eccentric / crank | Frame design: C-frame, single sided | Opening in table: yes | Total force (nominal): 250 to | Table surface (left-right): 800 mm | Table ...
Niederhelfenschwil, Switzerland - Trusted Seller
1980 BETZ EZL 300 40715
- Manufacturer: BETZ
approved for single stroke Safety valve make Herion Pneumatic clutch make Desch Motor grease - central lubrication ram weight - compensation cylinder Motorized height adjustment T-slots in the ram Freestanding co...
Niederhelfenschwil, Switzerland - Trusted Seller
2002 MIOS T20 FV 53991
- Manufacturer: Mios
Object: 53991 | Spigot hole diameter: 30 mm | Stroke rate (max.): 155 /min | Stroke min.: 5 mm | Stroke max.: 60 mm | Shut height (stroke down, adjustment up), bdc: 280 mm | Throat (c-frame): 180 mm | Tota...
Niederhelfenschwil, Switzerland - Trusted Seller
2000 PRESSIX 100 CNR 4 51223
- Manufacturer: Pressix
Located in Barcelona - Spain 2 identical units available
Niederhelfenschwil, Switzerland - Trusted Seller
BAR-STAY WITH ROLLS “METALLKRAFT” MS 3V
- Manufacturer: Metallkraft
- Model: MS3V
Height adjusting 530 – 870 mm, rolls width 2×125 mm
Biel/Bienne, Switzerland - Trusted Seller
FEINTOOL GKP 250 43972
- Manufacturer: FEINTOOL
Strip feed unit (without servo) for GKP or MFA 250T Strip thickness: 10 mm Strip width: 250mm DYNABOX 90 MEDIUM gearbox It is recommended to use: Servo motor BECKHOFF AM8062-0L20 Resolution 0.1mm
Niederhelfenschwil, Switzerland
Tip: Enter manufacturer, model or keyword