- Trusted Seller
Jamésie, Canada - Trusted Seller
Conc jet pump system incl.: (5) 6 mm rubber lined hoppers
used
- Manufacturer: JET
Conc jet pump system incl.: (5) 6 mm rubber lined hoppers, (1) Eriez vibratory feeder, valves c/w (2) Warman centrifugal pumps, mod. 75WBH, 100 hp ea. (2nd Loc. Red Zone, Level M)
Jamésie, Canada - Trusted Seller
UV-IR infra-red/UV dryer
used
UV-IR infra-red/UV dryer, ser. no. 11070 (2015) w/ Eriez feeder, infeed and outfeed chutes c/w Kason vibratory separator, ser. no. M-1047, 1/3 hp
Jamésie, Canada - Trusted Seller
Knelson KC-CVD32 Gold Centrifugal Concentrator
used
Continuously Variable Discharge Automated Controls Knelson ICS Independent Control System, See General Specs Below
Canada - Trusted Seller
Denver No. 18 Special Flotation Cells
used
- Manufacturer: Denver
Manual Cell to Cell Flow Control Gate Naturally Aspirated Sealed Standpipe
Canada - Trusted Seller
Holman-Wilfley 8000SD Concentrating Table
used
- Manufacturer: Holman-Wilfley Ltd
Capacity: Up to 2,500 kgs/Hour (Particle Size Dependent) | Deck type: Single Deck | Deck area: 7.5m² | Deck size: 1,600mm x 4,900mm | Water supply requirements: 20 - 35L/min | Drive: Baldor Electric Motor | Powe...
Canada - Trusted Seller
Neffco Centrifugal Bowl
used
- Manufacturer: Neffco
With Feed Trough Electrical Requirements: Overall Dimensions:
Canada - Trusted Seller
Mill, Sag, 38' X 25'5", Metso, 26,016 HP, Unused #D739643
used
- Manufacturer: Metso
Unused Metso sag mill, 38' (11.58 m) diameter x 25' 5" (7.76 m) long, 26,016 HP (19,400 kw) Siemens wrap around drive motor-operating frequency 50/60 Hz. EGL: 22' (6.7 m), mill speed: 7.5-10.08 RPM. Maximum volum...
Canada - Trusted Seller
Mill, Sag, 40' X 25', FL Smidth, 34,866 HP, Unused #D739644
used
- Manufacturer: FL Smidth
Unused FL Smidth SAG mill, 40' diameter x 25' length, designed for 34,866 HP (26,000 kW) wrap-around GMD motor (motor not included). No liners included.
Canada - Trusted Seller
Mill, SAG, 32' x 12', Hardinge-Koppers, 6800 HP Dual Drive #D744636
used
- Manufacturer: Hardinge
32' x 12' SAG mill, manufactured by Hardinge-Koppers, driven by dual GE 3400 HP 4000 V, 60 Hz AC wound rotor induction motors, model 108770. Complete with trunnions, trunnion liners, girth gear, pinion assemblies...
Canada - Trusted Seller
Mill, Sag, 13'6" X 4', Marcy, No Motor, #D739647
used
- Manufacturer: Marcy
Marcy Dry Grind SAG Mill, 13' 6" Diameter x 4' Long. Includes bull gear, pinion gear, large Falk gearbox, air clutch, and lube set. No motor. Manufactured new in 1988.
Canada - Trusted Seller
Knelson KC-CVD32 Centrifugal Concentrator
used
Continuous variable discharge. Fully automated control system. 40 hp baldor electric motor. Includes guarding, piping package, and spec sheet.
Savona, Canada - Trusted Seller
(New) Hy-G HR16 Concentrator with Deep Bowl Technology
used
- Manufacturer: Hy-G Concentrators Inc.
Recovering free gold and other heavy metals and minerals in crushing, milling, or recycling circuits. Reprocessing crushed and milled tailings to remove gravity recoverable gold and other heavy metals and minerals.
Savona, Canada - Trusted Seller
Denver No. 18 Sub-A Flotation Cells
used
Bank of 10. 18 cubic feet per cell. Sealed stand pipes. Forced air control valves. Cell to cell flow control gates. 7.5 hp motors - two cells/motor. Overflow discharge paddle shaft. Belt guards.
Savona, Canada - Trusted Seller
Denver Sub A #21 Flotation Cells
used
40 cubic feet per cell. Bank of 4. Cell to cell flow control gates. Launder overflow discharge. Paddle shaft. 10 hp motor per 2 cells. Natural rubber impellers and diffusers.
Savona, Canada
Tip: Enter manufacturer, model or keyword