Used Machine Tools in California, USA

CLEATBENDER RAMS 24" X 20 GA.

• Manufacturer: Rams

A manually operated tool that forms uniform drive cleat edges on rectangular ductwork in seconds without set-up or adjustment. The upper handle forms the cleat and the lower handle opens the tool for easy removal...

20 Ga. x 10' VAN-MARK max 20 GA / recommended 24 GA.

BENDING CAPACITIES: Capacities are based on standard metal properties. FEATURES: * Heavy-duty extruded aluminum shop stand included with every Mark IV. The * Xtreme Shop Stand will not rock, rattle, roll or rust....

3' X 22 GA. JET SLIP ROLLS JET STK#752022 USED

IMPORTANT CONDITIONS OF THIS QUOTATION: All relevant facts about the above machinery are believed to be accurate, but none are guaranteed. It is the sole responsibility of the buyer to verify all aspects of the ...

3' x 22 GA. JET SLIP ROLLS STK#756026

JET manual slip rolls have a forming width of 24", 36" & 50" with a capacity of 20, 22 & 16 gauge mild steel. These machines have two driven rolls of precision turned, ground and polished carbon steel. They are t...

15" JET VARIABLE SPEED DRILL 230/460V 3-PHS STK#354551

These JET Drill Presses use a variable-speed motor with the stepped-pulley system, and come equipped with a continuously variable transmission. This enables use at a wide range of speeds, as well as the ability t...

17" PALMGREN 16-SPEED FLOOR NEW

• Manufacturer: Palmgren

Palmgren's heavy duty 16-speed drill presses are designed and built for drilling a wide array of materials. They have the weight and rigidity to maintain the built-in tight tolerances required for metalworking ap...

20" PALMGREN 16-SPEED FLOOR NEW

• Manufacturer: Palmgren

Palmgren's heavy duty 16-speed drill presses are designed and built for drilling a wide array of materials. They have the weight and rigidity to maintain the built-in tight tolerances required for metalworking ap...

5' X 10 GA.(5/32") SAHINLER INITIAL PINCH ROLLS

• Manufacturer: Sahinler
• Model: IRM 1550 X 140

FEATURES: - MOVABLE FOOT CONTROL ON TRAILING LEAD - EMERGENCY STOP BUTTON ON THE CONTROL - LOW VOLTAGE AT THE CONTROLS - CONE BENDING ATTACHMENT - TILTABLE REAR ROLL - GROOVES IN ROLLS 3/8", 1/2" AND 5/8" ROUND B...

20" JET VARIABLE SPEED DRILL 3PH(OR 1PH !)220V STK#354214 #

*Can also run as 220V, Single Phase JET Electronic Variable Speed Drill Presses permit use at spindle revolution rates between 65 and 2000 RPM for a wide variety of applications. Designed to permit continuous spe...

5' X 10' WYSONG 2kW FIBER LASER

• Manufacturer: Wysong

Laser Power 2 Kw Type Fly Optic Maximum Sheet Size 5x10' (1500mm. x 3000 mm) Maximum Cutting Thickness Steel 0.63" (16 mm) Maximum Cutting Thickness Stainless steel 0.39" (10 mm) Maximum Cutting Thickness A...

20 Ga. x 12' VAN-MARK max 20 GA / recommended 24 GA.

BENDING CAPACITIES: FEATURES: * Heavy-duty extruded aluminum shop stand included with every Mark IV. The * Xtreme Shop Stand will not rock, rattle, roll or rust. Unit is fully detachable and collapsible for easy ...

20 Ga. x 6'6" VAN-MARK max 20 GA/recommended 24 GA

FEATURES: * Heavy-duty extruded aluminum shop stand included with every Mark IV. The * Xtreme Shop Stand will not rock, rattle, roll or rust. Unit is fully detachable and collapsible for easy fast setup and trans...

20 Ga. x 8'6" VAN-MARK max 20 GA/recommended 24 GA.

FEATURES: * Heavy-duty extruded aluminum shop stand included with every Mark IV. The * Xtreme Shop Stand will not rock, rattle, roll or rust. Unit is fully detachable and collapsible for easy fast setup and trans...

17" PALMGREN 16-SPEED FLOOR NEW

• Manufacturer: Palmgren

Palmgren's heavy duty 16-speed drill presses are designed and built for drilling a wide array of materials. They have the weight and rigidity to maintain the built-in tight tolerances required for metalworking ap...