Used Extruders in Illinois, USA

PROCESSING TECHNOLOGIES 50″ WIDE 3 6522

Processing Technologies, Inc. model 5024, 3 roll down stack. S/N 297-CRS. Manufactured in February, 2000. Has two (2) 24″ diameter x 50″ wide lower chrome rolls. Upper roll is 12″ x 50″. All chrome rolls are core...

CLOEREN 12″, 3 LAYER VANE 10872

Cloeren 12″ 3 layer vane die, S/N D.ND935-0103-01, job no. 91-935, mounted on a caster stand, three 1.5″ material entries on a Cloeren 3 layer co-ex block (a b c), job no. D-935-2001-01, S/N E-3lSP-1636, 0.001″ t...

EDI 28.5″ ULTRAFLEX H40 SHEET 6671

• Manufacturer: EDI

Extrusion Dies, Inc. 28.5″ Ultraflex H40 sheet die. S/N 89-12354. 0.001″ – 0.040″ lip opening 240 volt 350 watt heaters 1.25″ diameter rear material entry. Manufactured 4/89. 990 Lbs. mounted on 41″ centerline v-...

EDI 36″ SHEET DIE 2859

• Manufacturer: EDI

EDI Autoflex 36″ sheet die, S/N 859445. Rebuilt. 230-Volt with 3/4″ back center feed. Mounted on a stand.

EDI 89″ ULTRAFLEX H75 SHEET 12204

• Manufacturer: EDI

Extrusion Dies, Inc. 89″ Ultraflex H75 sheet extrusion die. S/N 00-21282. Manufactured in March of 2000. Lip opening dimensions are 0.01″ – 0.075″ with a 0.300″ lip land length. All flow surfaces are UltraChrome ...

KAYENESS GALAXY III 9052 CAPILLARY 14779

Kayeness Galaxy III model 9052 capillary rheometer, 4.5″ travel. Touch pad controls, on mount pads, in excellent condition.

WIRE COAT EXTRUSION DIE WITH 10650

Co-ex wire coating extrusion die, manufacturer unknown. 240-Volt heater bands, 1 3/4″ material entry.A possible application for this die would be wire insulation with a clear coat over the wire on the co-ex side ...

EREMA PC1007T FILM RECLAMATION LINE 18886

• Manufacturer: Erema

2012 Erema model PC1007T film reclaim lineS/N P11/232. Rated at 350-430 kgs/hour on LDPE and LLDPE and 300 kgs/hour on HDPE. line consists of the following:Model FB6000/900 inclined cleated in-feed conveyor measu...

EDI UHRC-100 44″ SHEET DIE 17461

• Manufacturer: EDI

One (1) used Nordson/ Extrusion Dies Inc Model Ultra-100 heavy duty sheet die with a 44″ slot opening. Integral upper flexible lip and fixed removable lower lip. Adjusting bolts on 1″ centers. 45 degree restricte...

EDI 59″ SHEET DIE 18873

One used Nordson / Extrusion Dies Inc model Ultraflex R-75 59″ heavy duty sheet die. S/N 73-1362-2-3. Integral upper flexible lip and fixed removable lower lip. Adjusting bolts on 1″ centers. 45-degree restrictor...

BATTENFELD / GLOUCESTER 1428HD GRANULATOR 18762

• Manufacturer: Battenfeld
• Model: Gloucester

Used Battenfeld Gloucester Model 1428HD Granulator having a 14” x 28” throat opening. Serial number1428-194. Three knife open rotor with slant cut is belt driven by a 200 HP Motor. Feed hopper modified for convey...

FULLY REBUILT BERINGER 12″ SCREEN 18492

Fresh fully rebuilt Beringer model 1200 Hydraulic screen plate screen changer. 12″ nominal breaker plates. 42″ center-line. With stand and 10 HP hydraulic power pack.2 Available – 2nd unit was put in service for ...

CLOEREN / PRODUCTION COMPONENTS 70″ 18339

One (1) used Cloeren / Production Components model Master-flex HD-40 sheet die with a 58″ slot opening. Heavy duty body. Integral upper flexible lip and fixed lower lip. Adjusting bolts on 1″ centers. 0.040″ flex...

PRODUCTION COMPONENTS 66″ SHEET DIE 18328

One (1) used Production Components Master Flex HD-40 sheet die with a 66″ slot opening. Heavy duty body. Integral upper flexible lip and fixed lower lip. Adjusting bolts on 1″ centers. 0.040″ flex adjustment. Coa...

CONAIR / WORTEX UP755 FEED 18253

• Manufacturer: Conair

Conair / Wortex model UP755 feed roll granulator. 4 knife rotor, 2 bed knife. Rotor is driven by a 20 HP 230/460-volt motor. Interlocked type steel feed rolls powered by a 1 HP A/C motor. Evacuated by a machine m...