Used Extruders

Trusted Seller
2001 DAVIS STANDARD PEDESTAL
- Manufacturer: Davis-Standard
- Model: PEDESTAL
Used 1.25" Davis Standard Pedestal Extruder With 36/1 L/D Vented Barrel. New 2001. Has electrically heated air cooled barrel, includes temperature control panel and 5 hp AC motor, 230/460 volt. Previously used as...
Hainesport, NJ
Trusted Seller
DAVIS STANDARD 4.5"
- Manufacturer: Davis-Standard
Used 4.5" Davis Standard 30/1 L/D Extruder, Electrically Heated Air Cooled Barrel. Includes gearbox with 17.36/1 gear ratio rated at 321 hp. Serial #M3316, SO #05432. New 10/1991. Includes Kryenborg Type K-SWE-12...
Hainesport, NJ
Buy Pre-Owned Coperion ZSK 160 Twin Screw Extruder — 8 Barrel Sections + Gear Re
- Manufacturer: WP
53949001 Used Werner Pfleiderer / Coperion Model ZSK 160 Twin Screw Extruder. Co-Rotating. Project No 87-3593. 8 barrel sections. Approximate 14' long screws. Approximate 26:1 L/D. Electrically heated. Gear Reduc...
Belvidere, IL
Buy Farrel Co-Rotating Twin Screw Extruder with Gala & Acrison Feeder
- Manufacturer: Acrison
54182001 Used Farrel Twin Screw Pelletizing Line Consisting Of: (1) Farrel 37 mm FTX80 co-rotating twin screw extruder, 5 zone electrically heated, water cooled, approximately 40:1 L/D. Driven by a 25 hp, 500 vol...
Belvidere, IL
Italtech Sandore Pasta Mixer Extruder – Model MX180DH | 200 kg/hr | 195mm Die | 8.5 kW | Built 2008
- Manufacturer: SandoreSandore
53530001 Used Italtech Sandore Pasta Mixer Extruder, Model MX180DH. 200 Kg/hour extrusion production; 30 kg extruder basin dough capacity; 50/kg mixer/kneader basin dough capacity; 195mm die dimension; Vacon X-Se...
Belvidere, IL
Trusted Seller
DAVIS STANDARD 150INDS-20
- Manufacturer: Davis-Standard
Used 1.5” Davis Standard Vented Single-Screw Extruder Model: 150IN DS-20 Driven by a nontagged motor and a Reliance model GV3000 AC drive Gearbox: 6.53:1 ratio, rated for 50 hp, 1.25 service factor, 152 rpm screw...
Hainesport, NJ
Trusted Seller
BATTENFELD GLOUCESTER 54" Wide
- Manufacturer: Battenfeld
Used 54" Wide Battenfeld Gloucester Co-Extrusion Sheet Extrusion Line, previously used for approximately 1200 lbs. per hour polypropylene sheet. Line consists of the following: (3) Acrison volumetric feeders with...
Hainesport, NJ
Trusted Seller
1991 DAVIS STANDARD 4.5"
- Manufacturer: Davis-Standard
Used 4.5" Davis Standard 30/1 L/D Extruder, Electrically Heated Air Cooled Barrel. Includes gearbox with 17.36/1 gear ratio rated at 321 hp. Serial #M-3315, SO #05432. New 10/1991. Includes Kryenborg Type K-SWE-1...
Hainesport, NJ
Trusted Seller
2000 DAVIS STANDARD 5.11"
- Manufacturer: Davis-Standard
Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...
Hainesport, NJ
Trusted Seller
1997 DAVIS STANDARD 5.11"
- Manufacturer: Davis-Standard
Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...
Hainesport, NJ
Trusted Seller
DAVIS STANDARD 1.5"
- Manufacturer: Davis-Standard
- Model: 15
Used 1.5" Davis Standard 28/1 L/D Non-Vented Air Cooled Extruder. New in 1989. Equipped with 6.53/1 gearbox ratio. Gearbox is belt driven through a 15 hp DC motor. Includes temperature control panel with motor dr...
Hainesport, NJ
Trusted Seller
WENGER X-155
- Manufacturer: Wenger
Used Wenger model X-155 extruder. (1) screw feeder with steam injection; (1) screw feeder with motor, no drive; (1) single-shaft pre-conditioner, cut-off knife. No control panel.
Hainesport, NJ
Trusted Seller
Gloucester 60mm
- Manufacturer: Gloucester
Used 2.36” (60mm) Gloucester 32/1 L/D vented single screw Extruder. Year 1986. Driven by a 50 hp DC motor and SCR control. Gearbox 9.48:1 ratio, serial 140. Barrel has 45” centerline height. Includes temperature ...
Hainesport, NJ
Trusted Seller
1994 HPM 3.5TMC-24
- Manufacturer: HPM
Used 3.5" 24/1 L/D HPM non-vented extruder. Model 3.5TMC-24, serial #93182. New 1994. Has electrically heated, air-cooled, barrel. Belt driven by a 75 hp brushless DC motor with controls. Flender gearbox type SZN...
Hainesport, NJ
High-Capacity Prealpina Single Screw Extruder – 1100 lbs/hr Production Rate
- Manufacturer: Prealpina
53309001 Used Prealpina 130 mm Diameter Single Screw Extruder, with a capacity of 1100 LBS/500 Kgs./hr. Electrically heated, air cooled. incl. die head and control panel. Reported to have new screw and barrel. Pr...
Belvidere, IL