Used Extruders

Trusted Seller
Auction
21.25" TRICAM IND. MODEL WP-20-06 WORK PLATFORMS, 20.5" HIGH
21.25" TRICAM IND. MODEL WP-20-06 WORK PLATFORMS, 20.5" HIGH
Toledo, OH
Visit Auction Website
Trusted Seller
Extruder 44.5 mm (1.75 in) - IPP# 85782
- Manufacturer: Welex
1.75" x 36" 1 1/2" inlet water cooled 2-zone steam heated Drive 20 HP, DC volt, 500 volt arm. 300 volt field motor, max 1750 rpm thru Lufkin gear reducer, 9.91:1 ratio, 175 rpm output speed. Mtd in frame 5' wide ...
Princeton Junction, NJ
GLOUCESTER 3.5″ 32:1 L/D EXTRUDER 18365
One (1) Used Gloucester model 35250R2 3.5″ 32:1 extruder having an electrically heated, air cooled, vented, and plugged barrel at approximately a 65″ center line height. S/N 36736/12. Barrel is set up for Contra-...
Elk Grove Village, IL
Auction
Contra Cool Blower for Extruder Cooling
2nd Level Mezz, Contra Cool Blower for Extruder Cooling Located in Alsip, IL.
Alsip, IL
Visit Auction Website
3.5″, EXTRUDER SCREW, 30:1 L/D 14756
3.5″ 30:1 extruder screw barrier mid-section, Previously ran PEP material.
Elk Grove Village, IL
Trusted Seller
Extruder 300 mm (11.8 in) - IPP# 237086
- Manufacturer: Milinda
Plodders single worm two stage. Rated for 2,000 kg./Hr.
Princeton Junction, NJ
GLOUCESTER 3.5″ 32:1 L/D EXTRUDER 18364
One (1) Used Gloucester model 35250R2 3.5” 32:1 L/D extruder. S/N 36736/11. Having an electrically heated, air cooled, and non-vented barrel at approximately a 65” center line height. Barrel is set up for Contra-...
Elk Grove Village, IL
HPM 3.5″ 30:1 L/D EXTRUDER 17578
One (1) used 3.5″30:1 HPM extruder having an electrically heated water cooled (closed loop) vented and plugged barrel at a 51 ½” centerline height. Koellmann gearbox is driven by a 100 HP D/C motor with a Eurothe...
Elk Grove Village, IL
KILLION 1″ 24:1 L/D EXTRUDER 16305
24:1 Killion pedestal extruder. S/N N6598 with a three (3) zone electrically heated air cooled barrel. Gearbox has a reduction ratio of 30:1 and is direct driven by a 3HP 1750/2050 RPM DC motor. Barrel can be rai...
Elk Grove Village, IL
WELEX 2″ 24:1 L/D EXTRUDER 17438
- Manufacturer: Welex
Welex model 200-24/1, 2″ 24:1 L/D extruder with a three (3) zone electrically heated, air cooled non-vented barrel at approximately a 50″ centerline height. Gearbox is a Koellmann Gear and is belt driven by a 20 ...
Elk Grove Village, IL
WAYNE 1.250″ 30:1 L/D EXTRUDER 16355
- Manufacturer: Wayne
Wayne 1.25″ extruder, S/N 9414-832. 30:1 L/D electrically heated, air cooled, vented (venting is plugged), barrel driven by a 7.5HP DC motor with SCR control 230-Volts input power. Includes track wheel base and a...
Elk Grove Village, IL
GLOUCESTER 2.5″ 32:1 L/D EXTRUDER 18366
One (1) Used Gloucester model 25225R2 2.5″ 32:1 extruder having an electrically heated, air cooled, and non-vented barrel at approximately a 65″ center line height. S/N 36736/25. Barrel is set up for Contra-Cool ...
Elk Grove Village, IL
Trusted Seller
Extruder 20 mm (0.79 in) Carbon Steel - IPP# 703671
Bone Brothers lab size single screw extruder. Unit has (4) electrically heated zones. Unit is complete with 7" diameter x 5" high stainless steel feed hopper cooling bath and control panel.
Princeton Junction, NJ
Barwell C3 Preformer
- Manufacturer: Barwell
One (1) Used Barwell C3 Preformer, Barwell_Rubber_Preformer, capacity 120 lbs, 10" x 55" chamber, Motor 460V, 60 Cycle, Max PSI 2500.
Cleveland, OH
WELEX 2″ 24:1 L/D CO-EXTRUDER 17576
- Manufacturer: Welex
One (1) used 2″ 24:1 L/D Welex co-extruder. Water cooled. Missing motor, drive panel, and pedestal. Last used on a sheet line.
Elk Grove Village, IL