Used Material Handling

CONAIR FRANKLIN DB12SE03MB DustBeater Vacuum Loader USED

• Manufacturer: Conair

4" Cylinder Height 7.25" Cone Height 12" Inside Cylinder 13.75" Filter Diameter 14.5" Inside Lid Cylinder 4.75" Bottom Inlet / Outlet Approx. 40.79 mm Tested Good Buyers are welcome to inspect equipment p...

Stainless Steel 55 Gallon Drums

55 gallon drums - stainless steel 304. Approx 11 drums with reinforcing bands, and 10 drums without reinforcing band. Drums have lids. Specify which kind - priced by the drum (minimum order 3 drums). Quantity (2...

UNA-DYN LS-45 Auto Loader USED

• Manufacturer: Una-Dyn

Self Contained with Lid and Filter Outside Diameter: 10" Inside Diameter: 9" Outlet 1 Inside Diameter: 1.25" Bottom Outlet Inside Diameter: 3" Flange: 7" x 5.5" Holes Center-to-Center: 6.5" x 5" 110 Volt ...

UNA-DYN 82894.06 Loader Used

• Manufacturer: Una-Dyn

82894.06 LID AND FILTER INCLUDED OD: 10" ID: 8 3/4" Outlet 1: 1 1/2" Bottom outlet: 2 1/2" Flange: 7" x 5 1/2" Bolt Holes, Center-to-Center: 6 1/4" x 4 3/4" Buyers are welcome to inspect equipment prior t...

Serco Hydraulic Dock Leveler 71" Wide Cylinder Lift No Controls 115V Power Unit

• Manufacturer: Serco

Used, in Good Working Condition. Removed From a Working Environment. This is setup with hydraulic power unit. 115V. No controls. The flip plate is 5/8" diamond plate. 71.25x20" This not a light duty unit. Main p...

AMI Spring Loaded Industrial Pallet Load Leveler 3500lbs 42x46" Swivel Top

• Manufacturer: AMI

Used, in Good Working Condition. Removed From a Working Environment. Not sure what weight the springs are set at. Swivel top 42x46". 30" high with no load. If this item ships as Flat Rate Freight please see detai...

CONAIR FRANKLIN Tilt Table Used

• Manufacturer: Conair

Tipper / Tilt Table Buyers are welcome to inspect equipment prior to purchase. Expedited shipping services are available upon request. This piece is located at Ideal Machinery, Inc. on our showroom floor. Loc...

AEC WHITLOCK Vacuum Loader SLC04 USED

• Manufacturer: AEC

115 Volt Single Phase 60 Hz Motor: 1.5 HP, 11 Amp 115 Volt Control Circuit Tested Good Buyers are welcome to inspect equipment prior to purchase. Expedited shipping services are available upon request. Th...

BUNTING MAGNETICS 81937 Drawer Magnet USED

• Manufacturer: Bunting

56.75 mm Diameter Inlet / Outlet Top Flange Approx. 7" x 7" Top Flange 50.67 mm Diameter Inlet / Outlet Bottom Flange Approx. 1.25" Cone Height 1.25" Cylinder Height Expedited shipping services are available...

EMI METAL FABRICATING Drawer Magnet USED

• Manufacturer: EMI

50.58 mm Diameter Inlet / Outlet Top Flange Approx. 7" x 7" Top Flange 7" x 7" Bottom Flange 5.5" x 5.5" Center to Center Holes Bottom Flange Approx. 69.71 mm Diameter Inlet / Outlet Bottom Flange Approx. Ex...

PPE Drawer Magnet USED

• Manufacturer: PPE

2" x 2" Inlet / Outlet Top 4.5" x 4.5" Top Flange 3" Bottom Cone Height 4.5" x 4.5" Bottom Flange 3" x 3.5" Center to Center Holes Bottom Flange 2" x 2" Bottom Inlet / Outlet Expedited shipping services are...

METAL FABRICATOR Drawer Magnet USED

• Manufacturer: METAL FABRICATOR

49.80 mm Diameter Top Flange Inlet / Outlet 6" x 6" Top Flange 5" x 5" Center to Center Holes Top Flange 7.5" Cylinder Height 1.25" Cone Height 1.25" Bottom Cylinder Height Expedited shipping services are a...

METAL FABRICATOR Drawer Magnet USED

• Manufacturer: METAL FABRICATOR

6.5" x 6.5" Top Flange 3" Diameter Inlet / Outlet Top Flange Approx. 3.25" Cone Height 6.5" x 6.5" Bottom Flange 5.5" x 5.25" Center to Center Holes Bottom Flange Approx. 3" Diameter Inlet / Outlet Bottom Fl...

METAL FABRICATOR Drawer Magnet USED

• Manufacturer: METAL FABRICATOR

7" x 7.25" Top Flange 76.71 mm Diameter Top Inlet / Outlet 2" Cone Height 1" Cylinder Height 7" x 7" Bottom Flange 5" x 5.75" Center to Center Holes Bottom Flange 51.75 mm Diameter Inlet / Outlet Bottom Fla...

METAL FABRICATOR Drawer Magnet USED

• Manufacturer: METAL FABRICATOR

3" x 3" Top Inlet / Outlet 6.5" x 6.5" Top Flange 5.25" x 3" Center to Center Holes Top Flange Approx. 3.25" Cone Height 6.5" x 6.5" Bottom Flange 3" x 5" Center to Center Holes Bottom Flange 3" X 3" Bottom...