Processing » Denmark

Building Filters

45

Refurbished Processing in Denmark

  • Alfa-Laval IFB 203S-33

    Alfa-Laval IFB 203S-33

    • Manufacturer: Alfa-Laval

    Separation module for cleaning mineral and diesel oils and other oils with low viscosity.

    Hirtshals, Denmark
  • Alfa Laval UVPX 207BGT-24 purifier

    Alfa Laval UVPX 207BGT-24 purifier

    • Manufacturer: Alfa-Laval
    • Model: UVPX

    The machine is in excellent condition and will be delivered with set of tools and manual. We have two units in stock - one in purificator - and one in concentrator configuration.

    Hirtshals, Denmark
  • NOVENCO centrifugal ventilator, type CT-800/100/R

    NOVENCO centrifugal ventilator, type CT-800/100/R

    • Manufacturer: Unknown

    Refurbished Novenco centrifugal ventilator type CT-800/100/R, pos. LG 0

    Hirtshals, Denmark
  • Westfalia pilot plant separator, type

    Westfalia pilot plant separator, type SA 1-02-575

    • Manufacturer: GEA
    • Model: SA

    This Westfalia pilot plant separator is reconditioned and in excellent condition. The separator comes with set of tools, separator manual and starter box. The separator is configurated to operate as a purifier - ...

    Hirtshals, Denmark
  • Alfa Laval IFB303X-73 separator module

    Alfa Laval IFB303X-73 separator module

    • Manufacturer: Alfa-Laval

    This Alfa Laval IFB303X-73 separator module is designed for the separation of tramp oil from cutting fluid - thereby prolonging the lifetime of the cutting fluid in the machine industry.

    Hirtshals, Denmark
  • Alfa-Laval AFPX 213XGT-14 purifier unit

    Alfa-Laval AFPX 213XGT-14 purifier unit

    • Manufacturer: Alfa-Laval
    • Model: AFPX-213

    Alfa Laval 3-phase centrifuge for fat and fish oil purification. Motor: 18,5 kW, 50 Hz, 400 V This reconditioned centrifuge has been spin tested at 50 Hz after completely reconditioning in our work shop. Video ...

    Hirtshals, Denmark
  • Contherm 6x11" Surface Scrape Heat

    Contherm 6x11" Surface Scrape Heat Exchanger unit in a rack

    • Manufacturer: Jensen & Nowak ApS

    One reconditioned Contherm 6"x11 surface scraped heat exchanger with center positioned rotor and flushed mechanical seals. 3" rotor with staggered pins for 14 blades, rotor diameter: 76 mm. In-board product head ...

    Hirtshals, Denmark
  • Alfa-Laval AFPX 213XGP-74 concentrator unit

    Alfa-Laval AFPX 213XGP-74 concentrator unit

    • Manufacturer: Alfa-Laval
    • Model: AFPX-213

    Alfa Laval 3-phase centrifuge for stick water concentration. Motor: 18,5 kW, 50 Hz, 400 V This reconditioned centrifuge has been spin tested at 50 Hz after completely reconditioning in our work shop and vibratio...

    Hirtshals, Denmark
  • Alfa Laval AFPX 213-75S concentrator

    Alfa Laval AFPX 213-75S concentrator unit

    • Manufacturer: Alfa-Laval
    • Model: AFPX-213

    Alfa Laval 3-phase centrifuge for stick water concentration. Motor: 18,5 kW, 50 Hz, 400 V. This separator has now been spintested at full speed and vibration measurements on video has been performed. The vibrati...

    Hirtshals, Denmark
  • Alfa-Laval Contherm surface scraped heat

    Alfa-Laval Contherm surface scraped heat exchanger, 6 x 9"

    • Manufacturer: Alfa-Laval

    Rack with one reconditioned horizontal Contherm 6 x 9" surface scraped heat exchanger with 5,5 or 7,5 kW gearmotor. We can supply new rotors in different diameters, new scraper blades, new bearing houses, new rot...

    Hirtshals, Denmark
  • Alfa Laval MAPX309BGT-14 separator

    Alfa Laval MAPX309BGT-14 separator

    • Manufacturer: Alfa-Laval
    • Model: MAPX

    Completely reconditioned Alfa Laval fuel oil separator. Motor: 11 kW, 50 Hz, 380 V. Capacity up to 7.000 l/hour. Capacity is depending on feed flow, amount of water in the feed, sludge content and oil viscosity ...

    Hirtshals, Denmark
  • 1997 Alfa-Laval WSPX403 separator

    1997 Alfa-Laval WSPX403 separator

    • Manufacturer: Alfa-Laval
    • Model: WSPX

    Reconditioned WSPX403 separator - configurated as an concentrator - and normally used for removal of solids particles and tramp oils from wash water. This unit has a 2,2 kW motor - 380 Volt, 50 Hz, 3 phase. The...

    Hirtshals, Denmark
  • POLLRICH suction ventilator with 75

    POLLRICH suction ventilator with 75 kW motor

    • Manufacturer: POLLRICH

    POLLRICH ventilator with 75 kW motor. Type SH45/RU560R630/GR90 no: 46856 / 75123 This ventilator is now completely reconditioned with new bearings etc. Technical specifications: V: 7,22 m3/s, n: 1800 rpm, Nw: 40,...

    Hirtshals, Denmark
  • Aerzen blower GLa 10.2

    Aerzen blower GLa 10.2

    • Manufacturer: Aerzen

    Reconditioned Aerzen blower unit - in as new condition. Motor: 5,5 kW, 50 Hz, 380 V.

    $3,050 USD
    Hirtshals, Denmark
  • Alfa Laval VNPX 407SGP-34 separator

    Alfa Laval VNPX 407SGP-34 separator for juice, wine and beverage clarification.

    • Manufacturer: Alfa-Laval
    • Model: VNPX-407

    For juice, wine and beverage clarification and polishing. Hydraulic capacity (pure water) is around 7.000 l/hour. The separator will be delivered including set of tools and manual. Motor: 11 kW, 380 V, 50 Hz.

    Hirtshals, Denmark
123

Overview

Processing equipment encompasses a wide range of machinery used in various industries to transform raw materials into finished products. This category includes machines like grinders, mixers, blenders, and specialized equipment for food, chemical, pharmaceutical, and other manufacturing processes. These machines are essential for improving efficiency, consistency, and quality in production lines.

FAQ

What should I consider when buying used processing equipment?

Consider the machine's condition, age, maintenance history, and whether it meets your specific processing requirements. It's also important to check for any signs of wear and ensure compatibility with your existing systems.

How do I arrange shipping for processing equipment?

Use a reliable transport service experienced in handling industrial machinery. Ensure the equipment is properly cleaned, secured, and protected during transit to avoid any damage.

What is the typical maintenance for processing equipment?

Regular maintenance includes cleaning, lubrication, inspection for wear and tear, and calibration. Follow the manufacturer's guidelines for specific maintenance schedules and procedures to ensure optimal performance and longevity.