Used processing and cutting in British Columbia, Canada

Hanchett Circular Saw Sharpener

• Manufacturer: Hanchett

- Model 724 - Serial #7731 - Good condition

84" SWING SAW - TWO (2) AVAILABLE

• Manufacturer: Canadian Mill Equipment

- 84" swing saw c/w 100 HP drive motor, 460/3/60 - Fabricated support frame - Hydraulic cylinder activated (no HPU) - Two (2) saw blades - Dismantled ready to load

Flare Saw Guide Resurfacer

• Manufacturer: Canadian Mill Equipment

- Single sided - Digitally controlled - Very accurate - 575 volt

Optimatic (Simonds) Model KRO970 Vertical Circle Saw Leveler

• Manufacturer: Optimatic (Simonds)

- Built in 2005 - Model KRO970 - 150mm min. diameter, 810mm maximum saw diameter - 1mm to 4mm flat thickness - Suitable for splined and slotted saw blades - 1155 hours - 480/3/60 - Dismantled and stored in a buil...

#54C Armstrong Manual Carbide Saw Post Grinder

• Manufacturer: Armstrong

- Saws from 6" to 48" diameter - Includes diamond wheel and adjustable saw mount to allow topping and facing operations - Motor - 1/2 HP, 208-220/440V, 50/60Hz - Floor space - 34" wide x 38" long - Height - 70" -...

2 Saw Valley Trimmer

• Manufacturer: Valley

- 8' to 20' lug loader - Lugged transfer deck - Near end trim saw - Cross over rollcase - Valley push back roll - Far end trim saw - Still installed

5' Salem Reducer Twin Sharp Chain System

• Manufacturer: Sharp

- To handle logs up to 24" in diameter x 16' long - Sprocket style log turner c/w overhead holddown rolls - 3" wide Sharp Chain c/w hydraulic drive - USNR reducer module c/w step disc head and linear positioners ...

COMACT DDM6 PROFILING CANTERLINE

• Manufacturer: Comact

- Built in 2006 - 4" to 10" diameter logs, 8 feet long @ up to 650FPM - Comact Wave Feeder (9' - 6" between end walls) - V flight Infeed Conveyor c/w eletric drive - V flight scan chain c/w electric drive - Quad ...

COMACT DDM6 FOUR (4) SIDED CANTER SYSTEM

• Manufacturer: Comact

- Built in 1997 - 4" diameter to 12" diameter - 3", 4" and 6" cants - up to 450 FPM - DDM6 - Feedroll log turner - quad roll c/w positioning cylinders - One (1) pair of vertical and one (1) pair of horizontal inf...

Sharp Chain Reducer Twin Bandmill System

• Manufacturer: Sharp

- To handle logs up to 18" in diameter x 20 feet long - VK log singulator - Sprocket style log turner c/w centering arms and overhead holddown rolls - 3" wide Sharp Chain c/w hydraulic drive - USNR reducer module...

Park Industries Yukon II Bridge Saw

• Manufacturer: Park Industries
• Model: Yukon

Specifications 240V 3 Phase 5.5 Amps 2019 model year Low Hours Mint Condition 45 degree tilt table 6′ x 11′ Table Wires remote control hand held

2005 MULTICAM 3000 Series

• Manufacturer: MultiCam
• Model: 3000 SERIES
• Phase type: Three-phase

Overview: Mild steel capacity: A high-definition model can cut up to 1.56" - 2.375" thick mild steel, depending on the plasma power source

2006 KELLER L-CUT 2-P5

• Manufacturer: Keller

Application: Fine Particulates | Horsepower: 7 hp | Voltage: 460 volts

2016 2016 Denver Tecnika 3500 5 – Axis Bridge Saw

Specifications Model Tecnika 200V 49A 3 Phase 5 Axis 1806 Operation Hours 360 Degree Head Rotation Y Axis Extension Vacuum Lift/Tilt Table with Rubber Bed Line & Dot Lasers Probe for Slab Thickness CSA Approved H...

66" Kockums Cut Off Saw

• Manufacturer: Kockums

- 50 HP motor, 460 volt, 1200 RPM - Still installed