Used logging in Canada

2017 Electric Crown TSP7000-33

• Manufacturer: Crown
• Model: TSP 7000
• Hours: 5,723 hour
• Lifting capacity: 3,300 kilogram

⚙️ 2017 Crown TSP7000-33 – 3,300 lb Electric Man-Up Turret Forklift | MonoLift Mast 423” | Dual 72V Batteries | Wire Guidance | CSA Certified | Brampton ON 🔋 Reconditioned | CSA/MOL Certified | Dual Lead-Acid Ba...

2020 Crown TSP6500-33

• Manufacturer: Crown
• Model: TSP 6500
• Hours: 625 hour
• Lifting capacity: 1,496.8536 kilogram

⚙️ 2020 Crown TSP6500-33 – 3,300 lb Electric Man-Up Turret Forklift | MonoLift Mast 231” | Lithium Battery | Wire Guidance | CSA Certified | Brampton ON 🔋 Reconditioned | CSA/MOL Certified | 72V Lithium Battery ...

Sanborn MinMax 36" Bandmill Headrig

• Manufacturer: Sanborn

- Extended column 4000 pound air strain - Hydraulic strain and tilt motor - 8 knife saw path cleaner - Hoe type saw guides - 36" saw line capacity - 100 HP, 1775 RPM arbor motor, 460/3/60 - 20' IGUS 5050 cable ca...

Hoba Bandblade Slicer HSA-2

• Manufacturer: Hoba

Fully automatic slicer from Hoba for different types of bread to use in a semi or fully-automatic line. Continuously rotating band blades are cutting identical slices with every cut. The blades are from hardened...

1997 ECONOMIZER

• Manufacturer: ECONOMIZER

1997 ECONOMIZER WOOD PROCESSOR (07CS- 6510) - Built in 1997 - 3" to 10" diameter logs - 2"x 2" up to 6" x 6" cants - Economizer Four (4) sided canter c/w saw section (up to 3 saws) - Three (3) strand infeed ...

10" Chip-N-Saw Mark II

• Manufacturer: Chip-N-Saw

- Build in 1978 - Forano knuckle style log turner - 18' half taper infeed c/w overhead hold down rolls and servo positioned lift - Mark II four sided canter - 2 x 4 spline bottom head - Drum style side heads c/w ...

20" Chip-N-Saw Line

- Infeed chain conveyor - Log turner - Single length infeed for 20' c/w holddown rolls and servo positioner for bed lift - 4 sided canter (bottom head (2 x 4 spline), side heads and top head c/w servo positioners...

44" NICHOLSON A2 RH AIR SEAL DEBARKER

• Manufacturer: Nicholson

- Built 1995 - Minimum log diameter is 4-1/2" - Five (5) Tool Air seal ring c/w remote tool tensioning - 100 HP, TEFC, 460 volt ring drive motor - Hydraulic ring centering - Fabricated main frame (appears in good...

2004 KENWORTH T800

• Manufacturer: Kenworth
• Model: T800
• HP: 550 horsepower
• Mileage: 656,197.7885 mile

2004 Kenworth T800 Daycab heavy spec tandem Day Cab ***Located near Westlock, AB KMS: 1,056,050 HRS: 21,903 Cummmins long block engine installed 8,000 hrs ago in 2011 Transmissions also replaced. Just had new cl...

COMACT DDM6 FOUR (4) SIDED CANTER SYSTEM

• Manufacturer: Comact

- Built in 1997 - 4" diameter to 12" diameter - 3", 4" and 6" cants - up to 450 FPM - DDM6 - Feedroll log turner - quad roll c/w positioning cylinders - One (1) pair of vertical and one (1) pair of horizontal inf...

BM&M 6 X 12 CHIP SCREEN (4 ONLY)

• Manufacturer: BM&M
• Model: 6X12

BM&M 6 X 12 CHIP SCREEN (4 ONLY) - each screen has 2 decks but no bottom pan. Screens were originally installed at West Coast Cellufibre (Vancouver) at their whole log chipping facility. All fines dropped direct...

CAE Sharp Chain Reducer Quad Bandmill System

• Manufacturer: Sharp

- Knuckle style log turner - Centering infeed conveyor consisting of: - Four (4) pairs of idling centering rolls c/w mechanical centering linkages assembly - One (1) pair of hydraulically driven spiked feedrolls ...

Comact DDM10 Line

• Manufacturer: Comact

- 10 years old - Approx. 120' V-flite conveyor including drive and attached control devices - Flying log turner - new HD upgrade 2011-12? (Quad roll) - DDM10 full profile machine, 480 volt - All drive units, moto...

GOOD NATURE HTST FLASH PASTEURIZER - MODEL FPXT-264

• Manufacturer: Good Nature Co.

(1) Used Good Nature HTST Flash Pasteurizer, Model FPXT-264. Manufactured in 2015, this unit heats and cools product in a series of stainless steel heat exchangers. Product is rapidly heated, held at temperature ...