Used dcs in New Jersey, USA

RDN EMC3DC

• Manufacturer: RDN

Used RDN Fly Knife Cutter for Maximum 3" Diameter Product Model EMC3DC Serial #33183 New 7/1994 Includes operator controls Click on the link below to see a video of the machine running.

24" x 12"

Used 24" Wide 3-Roll Down-Stack Cooling Roll Stack (3) 12" diameter rolls Approximately 5' cooling conveyor Rbber to metal pull roll assembly Chill rolls driven by a 5HP DC motor without drive Pull rolls are driv...

Wayne 1.25"

• Manufacturer: Wayne

Used 1.25” Wayne Single-Screw Extruder Driven by a 7.5 hp DC motor with SCR control,230 volt

4" ASR Film Hopper

• Manufacturer: ASR

Used ASR Film Hopper with 4" OD exit screw. Double wall design hopper for feeding film fluff and pellets. 1 hp DC motor, 180 volt, 1750 rpm

JOHNSON

• Manufacturer: Johnson

Used Johnson roll pull roll stand Has (2) 54" x 8" diameter rubber covered rolls Rolls are driven by 10 hp DC motor Drive-All 4-speed gearbox Air actuated top pull roll

CINCINATTI MILACRON 34" Wide

• Manufacturer: Cincinnati

Used 34" wide Cincinatti Milacron 2-roll sheet take-off with 34" face X 18" diameter rolls. Rolls are mounted in a vertical stack arrangement. Chromed and cored rolls with rotary unions, silent chain driven with ...

BRABENDER 88

• Manufacturer: Brabender

Used 25mm 24/1 L/D Brabender twin screw extruder package. Has air cooled extruder, temperature control panel, type D10002, prep center with model 088 type 09-25-000 temperature pressure module. Includes 10 HP DC ...

BERLYN 2"

• Manufacturer: BERLYN

Used 2” Berlyn Single-Screw Extruder Manufacturer: Berlyn Belt driven by a 40 hp DC motor, 460 volt, with Allen Bradley Model 1395 SCR through a Koellmann gearbox Gearbox: size PEZS 312, 19.95:1 reduction ratio, ...

Gloucester 60mm

• Manufacturer: Gloucester

Used 2.36” (60mm) Gloucester 32/1 L/D vented single screw Extruder. Year 1986. Driven by a 50 hp DC motor and SCR control. Gearbox 9.48:1 ratio, serial 140. Barrel has 45” centerline height. Includes temperature ...

Betol 4024 Extruder - IPP# 104127

• Manufacturer: Betol

extrusion/film line (4) 12 KW for barrel w/screw speed indicator and ammeter Electrical supply 3 phase, 50 cycle, 380/440 volt Screw and barrel made of high grade corrosion resistant steel alloy (1) Betol Mdl 025...

DAVIS STANDARD 1.5"

• Manufacturer: Davis-Standard
• Model: 15

Used 1.5" Davis Standard 28/1 L/D Non-Vented Air Cooled Extruder. New in 1989. Equipped with 6.53/1 gearbox ratio. Gearbox is belt driven through a 15 hp DC motor. Includes temperature control panel with motor dr...

Extruder 44.5 mm (1.75 in) - IPP# 85782

• Manufacturer: Welex

1.75" x 36" 1 1/2" inlet water cooled 2-zone steam heated Drive 20 HP, DC volt, 500 volt arm. 300 volt field motor, max 1750 rpm thru Lufkin gear reducer, 9.91:1 ratio, 175 rpm output speed. Mtd in frame 5' wide ...

1994 HPM 3.5TMC-24

• Manufacturer: HPM

Used 3.5" 24/1 L/D HPM non-vented extruder. Model 3.5TMC-24, serial #93182. New 1994. Has electrically heated, air-cooled, barrel. Belt driven by a 75 hp brushless DC motor with controls. Flender gearbox type SZN...

WERNER & PFLEIDERER ZSK20

• Manufacturer: WP
• Model: ZSK20

Used Werner & Pfleiderer model ZSK40, 40mm co-rotating twin screw extruder. 1990 model year. 46:1 L/D vented barrel with 11-barrel sections and a 41" centerline height. Driven by 50 hp 500 volt 1750/2100 rpm DC m...

1997 DAVIS STANDARD 5.11"

• Manufacturer: Davis-Standard

Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...