- Trusted Seller
2000 DAVIS STANDARD 5.11"
- Manufacturer: Davis-Standard
Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...
Hainesport, NJ - Trusted Seller
2002 LEISTRITZ ZSE 100
- Manufacturer: Leistritz
Used Leistritz 100mm Co-Rotating Twin Screw Extruder. Model #ZSE 100 GLAAX, serial #3092, new 2002. Driven by 330 kw (442 hp), 1600 rpm DC motor with SCR control. Has 300 rpm screw speed, rated at 5000 Newton met...
Hainesport, NJ - Trusted Seller
DAVIS STANDARD 4.5"
- Manufacturer: Davis-Standard
Used 4.5" Davis Standard 30/1 L/D Extruder, Electrically Heated Air Cooled Barrel. Includes gearbox with 17.36/1 gear ratio rated at 321 hp. Serial #M3316, SO #05432. New 10/1991. Includes Kryenborg Type K-SWE-12...
Hainesport, NJ - Trusted Seller
1991 DAVIS STANDARD 4.5"
- Manufacturer: Davis-Standard
Used 4.5" Davis Standard 30/1 L/D Extruder, Electrically Heated Air Cooled Barrel. Includes gearbox with 17.36/1 gear ratio rated at 321 hp. Serial #M-3315, SO #05432. New 10/1991. Includes Kryenborg Type K-SWE-1...
Hainesport, NJ - Trusted Seller
Extruder 69.9 mm (2.8 in) Stainless Steel 316 - IPP# 703669
- Manufacturer: Reifenhausser Kg
single screw extruder line General purpose screw and feed hopper. Production rate: 75 Kg/hr maximum polypropylene. Barrel has (8) heaters with (3) electric fans Extruder driven by a 60 HP (46 KW) DC motor. Line i...
Princeton Junction, NJ - Trusted Seller
2002 COPERION 2.3"
- Manufacturer: Coperion Waeschle
Used 58mm Coperion Co rotating Mega Compounder with 11 barrel sections (34/1 L/D) and side feeder, New 3/2002. Has electrically heated water cooled barrel. Direct connected to 500 hp DC motor with SCR controller....
Hainesport, NJ - Trusted Seller
1994 LEISTRITZ MICRO 18
- Manufacturer: Leistritz
Used 18mm approximately 28/1 L/D Leistritz Micro-18 Co-Rotating Twin Screw Extruder, serial #473614, new 1994. 500 RPM screw speed. 6 Barrel Segments, Top Ports In Segments 1, 2, and 6. 6 Barrel Zones Controlled ...
Hainesport, NJ - Trusted Seller
BUSS 200 HP
- Manufacturer: Buss
Used 100mm Buss kneader with 9/1 L/D barrel. Driven by 200 hp DC motor, includes 5.94/1 gearbox, jacketed barrel and clam shell barrel opening. Includes operator control panel. Kneader will discharge into approxi...
Hainesport, NJ - Trusted Seller
MARSHALL & WILLIAMS 54" Wide
- Manufacturer: Marshall
Used Marshall and Williams sheet take-off unit consisting of (3) 54" face rolls mounted in a vertical arrangement for a downstack operation. All three rolls measure 16" in diameter and are ceramic coated. Top and...
Hainesport, NJ - Trusted Seller
1995 HPM TMIII
- Manufacturer: HPM
- Model: TMIII
Used 4.5” HPM Single Screw Extruder 30/1 L/D Model: TMIII Year: 1995 6" x 6" top center feed throat Driven by a 250 hp DC motor, 460 volt AC input and a Powertec motor control with 460 volt 50/60 Hz AC input. Gea...
Hainesport, NJ - Trusted Seller
Reifenhauser FAV 120/68
- Manufacturer: Reifenhäuser
Used 47" wide Reifenhauser nip roll assembly. Type FAV 120/68, . 0263/68, Mach. No. 670. Has 8" diameter rubber/metal rolls with air actuated cylinder, Driven by a 3/4 HP, 90 arm volts DC drive.
Hainesport, NJ - Trusted Seller
DAVIS STANDARD 48"
- Manufacturer: Davis-Standard
Used Davis Standard sheet take-off unit consisting of (3) 48" face rolls mounted in a vertical arrangement for a downstack operation. All three rolls measure 16" in diameter. Top roll is tungsten and the middle a...
Hainesport, NJ - Trusted Seller
1991 DAVIS STANDARD 100MM35F
- Manufacturer: Davis-Standard
- Model: 100MM35F
Used 100mm Davis Standard 30/1 L/D non-vented Extruder. Model 100MM35F, Serial #M3027, new 12/1991. Has barrel, electrically heated, water cooled barrel. Driven by a 125 HP Reliance DC motor but no SCR control. G...
Hainesport, NJ - Trusted Seller
Extruder 38.1 mm (1.5 in) Aluminum - IPP# 78337
- Manufacturer: Sterling
Sterling Having 3-zone electrically heated water cooled non-vented Xaloy 306 lined barrel. Barrel water cooling system utilizes cast aluminum heaters in a closed loop system including reservoir pump and heat exch...
Princeton Junction, NJ - Trusted Seller
Werner & Pfleiderer CRP 104
- Manufacturer: WP
Used Werner & Pfleiderer conical counter-rotating twin screw extruder. Type # CRP 104, serial# 180115, project # 84 3220. Screws are 102.2 mm at feed tapering to 75.5 mm at discharge. Approximately 17:1 L/D ratio...
Hainesport, NJ
Tip: Enter manufacturer, model or keyword