Used Mineral Processing in Canada

Flotation Cell #2 Equipped w/ (1) TOSHIBA 75 Hp, Motor 1800 (RPM) 365T Frame, s/n. 20020023703 & (1)

• Manufacturer: Toshiba

Flotation Cell #2 Equipped w/ (1) TOSHIBA 75 Hp, Motor 1800 (RPM) 365T Frame, s/n. 20020023703 & (1) POSEIDON Pump (Loc. building 10 Upstairs float cell room)

Flotation Cell # 1 Equipped w/ (1) (2012) Air Pressure Tank, 110 (psi) @ 200 F,s/n. 8646-01 (1)

Flotation Cell # 1 Equipped w/ (1) (2012) Air Pressure Tank, 110 (psi) @ 200 F,s/n. 8646-01 (1) TOSHIBA 25 Hp, Motor 3540 (RPM) 284T Frame, s/n. 20020023703 & (1) POSEIDON Pump (Loc. building 10 Upstairs float ce...

Warman sump-pump

• Manufacturer: Warman

Warman sump-pump, mod. V15F03, 20 hp c/w valves

Conc jet pump system incl.: (5) 6 mm rubber lined hoppers

• Manufacturer: JET

Conc jet pump system incl.: (5) 6 mm rubber lined hoppers, (1) Eriez vibratory feeder, valves c/w (2) Warman centrifugal pumps, mod. 75WBH, 100 hp ea. (2nd Loc. Red Zone, Level M)

UV-IR infra-red/UV dryer

UV-IR infra-red/UV dryer, ser. no. 11070 (2015) w/ Eriez feeder, infeed and outfeed chutes c/w Kason vibratory separator, ser. no. M-1047, 1/3 hp

Denver D-1 Lab Flotation Cell

• Manufacturer: Denver

Tachometer Not Installed Stainless Steel Wetted Parts (Urethane impeller and diffuser). Comes with 750mL Stainless Steel Tank

Denver No. 18 Special Flotation Cells

• Manufacturer: Denver

Manual Cell to Cell Flow Control Gate Naturally Aspirated Sealed Standpipe

Holman-Wilfley 8000SD Concentrating Table

• Manufacturer: Holman-Wilfley Ltd

Capacity: Up to 2,500 kgs/Hour (Particle Size Dependent) | Deck type: Single Deck | Deck area: 7.5m² | Deck size: 1,600mm x 4,900mm | Water supply requirements: 20 - 35L/min | Drive: Baldor Electric Motor | Powe...

(New) Duplex 12 in x 12 in High Efficiency Mineral Jig

Duplex High Efficiency Mineral Jig. Equipped with: 2 hp electric motor. Recovers higher placer gold values than riffles. Shipping information:

(New) Duplex 42 in x 42 in High Efficiency Mineral Jig

Duplex High Efficiency Mineral Jig. Please see specs tab below for capacities and requirements. Recovers higher placer gold values than riffles. Specifications if used as Rougher Jig Specifications if used as Cle...

Mill, Sag, 38' X 25'5", Metso, 26,016 HP, Unused #D739643

• Manufacturer: Metso

Unused Metso sag mill, 38' (11.58 m) diameter x 25' 5" (7.76 m) long, 26,016 HP (19,400 kw) Siemens wrap around drive motor-operating frequency 50/60 Hz. EGL: 22' (6.7 m), mill speed: 7.5-10.08 RPM. Maximum volum...

(New) Duplex 26 in x 26 in High Efficiency Mineral Jig

Duplex High Efficiency Mineral Jig. Please see specs tab below for capacities and requirements. Recovers higher placer gold values than riffles. Specifications if used as Rougher Jig Specifications if used as Cle...

Mill, SAG, 32' x 12', Hardinge-Koppers, 6800 HP Dual Drive #D744636

• Manufacturer: Hardinge

32' x 12' SAG mill, manufactured by Hardinge-Koppers, driven by dual GE 3400 HP 4000 V, 60 Hz AC wound rotor induction motors, model 108770. Complete with trunnions, trunnion liners, girth gear, pinion assemblies...

Mill, Sag, 13'6" X 4', Marcy, No Motor, #D739647

• Manufacturer: Marcy

Marcy Dry Grind SAG Mill, 13' 6" Diameter x 4' Long. Includes bull gear, pinion gear, large Falk gearbox, air clutch, and lube set. No motor. Manufactured new in 1988.

Mill, Sag, 40' X 25', FL Smidth, 34,866 HP, Unused #D739644

• Manufacturer: FL Smidth

Unused FL Smidth SAG mill, 40' diameter x 25' length, designed for 34,866 HP (26,000 kW) wrap-around GMD motor (motor not included). No liners included.