Erie, PA
NRM 3.5" 8:1 L/D Rubber Extruder
used
- Manufacturer: NRM
One (1) NRM 3.5" 90mm Cold Feed Rubber Extruder, 8:1 L/D, 20.64:1 gearbox ratio, Reliance 50 HP 1750/2100 RPM 500 VDC motor, straight delivery head, forced lube system, non-power feed roll type, S/N T37835
Cleveland, OH
NRM 3-1/2 Cold Feed Rubber Extruder
used
- Manufacturer: NRM
One (1) Rebuilt NRM 3.5" 90mm 3 1/2" Cold Feed Rubber Extruder, 12:1 L/D, 75 HP 1750 RPM 500 VDC motor, 24.9:1 gearbox ratio, roller feed / power feed roll, approximately 14 week delivery.
Cleveland, OH
NRM Duplex 6 x 10 Duplex Tread Extruder
used
- Manufacturer: NRM
One (1) used NRM 6” x 10 Duplex Hot Feed ROLLERFEED tread extruder, opposed head, NRM 10” with 27:1 gearbox ratio, WITHOUT 6" EXTRUDER, duplex opposed head, no motors, no base, removed from service due to plant c...
Cleveland, OH
NRM Rebuilt 4.5 Cold Feed Extruder 17:1 L/D
used
- Manufacturer: NRM
One (1) Rebuilt NRM 4.5" 120mm 4 1/2" Cold Feed Rubber Extruder, 17:1 L/D, 125 HP DC 1150/2000RPM 500V motor, Kwik clamp head, roller feed
Cleveland, OH
NRM 120mm Cold Feed Rubber Extruder 12:1 L/D
used
- Manufacturer: NRM
One (1) Rebuilt NRM 4.5" 120mm 4 1/2" Cold Feed Rubber Extruder, 12:1 L/D, 25.14:1 G/B ratio, 100 HP DC, 1150/2000 RPM, 550 V motor, clamp type head, roller feed / power feed roll, approximately 14 week delivery.
Cleveland, OH- Trusted Seller
NRM Pacemaker 3 Extruder
used
- Manufacturer: NRM
2.5" NRM Pacemaker 3 Extruder / Air Cooled 24:1 L/D 15.2:1 Gearbox Ratio 75 HP AC Motor Magnetek GPD515 AC Drive 4 Barrel Zones 4 Die Zones Omron Esak Temperature Controllers Air Cooled Barrel Amp Meter ...
- Trusted Seller
3.5" NRM Profilemaster Extruder, 24:1, L/D, 60Hp
used
- Manufacturer: NRM
Used 3.5" NRM Profilemaster Extruder, S/N: 17749, Vintage: 09/1980 42.5 Centerline Height, Round Feed Throat, Air-Cooled Barrel Clamp Barrel Flange, Screw and Hopper Included 60HP DC 1750 RPM Emerson Motor Fan Co...
United States - Trusted Seller
Extruder, 2.5" dia, NRM, Mdl 2-5-24.1, 40 HP, Plastics, #S739219
used
- Manufacturer: NRM
NRM extruder, 2.5" diameter x 24" long plastics extruder, model 2-5-24.1 PM IV RH-1CANVTD, single head carbon steel extruder. Unit is electrically heated, air cooled 4 zone non-vented barrel, water reed throat wi...
San Dimas, CA 
NRM 8" Sheeting Head Rubber Extruder
used
- Manufacturer: NRM
One (1) Used NRM Sheeting Head for 8" NRM or Davis Standard rubber extruder, produces up to 20" wide rubber sheets
Cleveland, OH
NRM 6"EXTRUDER
used
- Manufacturer: NRM
"NRM" Extruder cold feeding with universal head to install die. In good operating condition. 6" screwdiameter, length 74.5” approximately L/D ratio approximately 12.5:1 Hot feeding and with mechanical roller...
Leon, Mexico
NRM PM III
used
- Manufacturer: NRM
Extruder Used NRM PM III Extruder for Sale. This pre-owned NRM plastic extruder is located in The United States and available to be seen under power for an inspection. If you have any questions regarding this N...
USA
Tip: Enter manufacturer, model or keyword