Used Machine Tools in Shizuoka, Japan

2012 Orii AFC05GAFP
- Manufacturer: Orii
Orii 500mm NC Roll Feeder AFC05GAFP Width: 20mm-500mm, Thickness: 0.2t-3.2t, Top Speed: 1.0m/sec Left → Right
Hamamatsu, Japan
OSG PSE11R030SS32-3L
- Manufacturer: OSG
OSG-PHOENIX 30mm/Shaper Cutter Straight Shank PSE11R030SS32-3L Flat/Side/Groove Rough-Finish O.D. 30mm, Max. depth of cut 10mm, Shank 32mm, Length under neck 90mm, Total length 190mm, 3 blades This was an unopene...
Hamamatsu, Japan
Rhombic 35° OD Turning Holder
- Manufacturer: Tomoe Co. Ltd.
Unknown Rhombic 35° OD turning holder One-round length of the sheet approx. 15,3mm Total length 150mm Shank 25×25 right hand side
Hamamatsu, Japan
Tungaloy PSKNR2525
- Manufacturer: Tungaloy
Tungaloy Square 90° OD Turning Holder PSKNR2525 O.D./Edge face, depth of cut 75°, cutting edge length 12°, chip relief angle 0°, right-hand side, shank 25*25mm
Hamamatsu, Japan
S25RMCLNL12
- Manufacturer: Tomoe Co. Ltd.
Rhombic 80° Internal Diameter Holder S25RMCLNL12 Min. machining diameter 32, 0° relief angle, 95° depth of cut, shank 25, with oil hole, left-hand side, multi-clamp type
Hamamatsu, Japan
OSG PSE11R030SS32-3L
- Manufacturer: OSG
OSG-PHOENIX 30mm/Shaper Cutter Straight Shank PSE11R030SS32-3L Flat/Side/Groove Rough-Finish O.D. 30mm Max. depth of cut 10mm Shank 32mm Neck 90mm length, 190mm length, 3 blades The package was unopened, but was ...
Hamamatsu, Japan
Tungaloy PSKNR2020
- Manufacturer: Tungaloy
Tungaloy Square 90° OD Turning Holder PSKNR2020 O.D./Edge Cutting Angle 75°Cutting Edge Length 12 Chip Fleece Angle 0°Right Handed Shank 20*20mm
Hamamatsu, Japan
2020 Dymac R40
- Manufacturer: Daimaku
DIMAC 400mm NC Roll Feeder R40 Width - 400mm, Thickness - 3.2t, Feed Length 0.01mm - 9999.99mm 80mm Width/3.2t, 200mm Width/2.6t, 300mm Width/1.6t Left to Right
Hamamatsu, Japan
Tungaloy EXN03R025M25
- Manufacturer: Tungaloy
Tungaloy 25mm/screw type high feed cutter EXN03R025M25,0-05-C Open when photographed Flat/groove/inclined cut/vertical Cutting blade diameter 25mm, maximum depth of cut 1mm, shank diameter 25mm, length under neck...
Hamamatsu, Japan
CERADEX PVPNR2020K-16Q
- Manufacturer: CERADEX
CERADEX Rhombic 35° OD Turning Holder PVPNR2020K-16Q O.D., end face, copying, depth of cut P:117,5°, cutting edge length 16°, chip relief angle 0°, right-hand side, shank 20*20mm
Hamamatsu, Japan
Kyocera 21mm/MCSE Type Chamfer End Mill MCSE106
- Manufacturer: 京セラ
Kyocera 21mm/MCSE Type Chamfer End Mill MCSE106 Groove/Chamfer Angle 45° Shank 20mm, Head Length 41mm, Total Length 121mm, 1 Flute
Hamamatsu, Japan
Tungaloy TID220F25-5
- Manufacturer: Tungaloy
Tungaloy 22,9mm/head interchangeable drill TID220F25-5 unopened Diameter 22-22,9mm, shank diameter 25mm, shank length 56mm, groove length 114mm, total length 200mm This item is unopened. Only the first photo show...
Hamamatsu, Japan
OSG P5D1500FS20M04
- Manufacturer: OSG
OSG-PHOENIX 15mm/5D type indexable drill P5D1500FS20M04 when photographed Blade diameter 15mm, drilling hole depth 75mm, maximum drilling diameter 15,8nn, total length 140mm, shank diameter 20mm, shank length 50m...
Hamamatsu, Japan
Tungaloy TID220F25-5
- Manufacturer: Tungaloy
Tungaloy 22,9mm/head interchangeable drill TID220F25-5 Open when photographed Diameter 22-22,9mm, shank diameter 25mm, shank length 56mm, groove length 114mm, total length 200mm This was an unopened item, but was...
Hamamatsu, Japan
OSG-WALTER F2042-25
- Manufacturer: OSG-WALTER
OSG-WALTER 25mm/Throwaway End Mill F2042-25×SS20 Cutting edge diameter 25mm, shank 20mm, total length 134mm, 2 blades
Hamamatsu, Japan