Building Filters
12 & 14 Station TDFC Dual Head Rollformer for Duct Lines
- Manufacturer: Ductformer
- Model: TDFC
The TDFC Flange application has proven to be the most cost effective method to construct and install commercial rectangular ductwork. The C-Style Flange provides the extra strength and rigidity to sustain the Air...
Sutton, MA
TK 24 Ga. Pitts. with Stand
- Manufacturer: Pitts
On the job site or in the shop, this portable little rollformer is a work horse for 24 gauge and lighter material. It is available with power flanging attachment and is perfect for field use. Steel stand include...
Drive Turn Hemmer
- Manufacturer: Flagler
Rollform your drive turn hems on this machine after notching and prior to bending into L or full wrap sections. Simple select the sections to be hemmed with the selector switch and run through. The machine will...
Sutton, MA
TK T-D-P Roll Former (w/TDP & Clip Rolls)
(Produces either TDC or TDF flanges). At last, an affordable, full service, high quality transverse duct connector machine!!! This 14 station roll former comes standard with TDC or TDF Rolls, Slitter and Clip Rol...
12 & 14 Station TDFC Dual Head Rollformers
Ductformer’s Dual Head TDFC Rollformer is designed for installation in existing Duct Coil Lines or can be used as a Free Standing Unit. The Rollformer is designed to accept and form either the F-Style (CR14-TDFC)...
Sutton, MA
TK No. 24 Collar Maker
Capacity: 24-30 Gauge Speed: 30ft./minute Notch,bead,crimp and roll complete round starting collars, 3″ to 14″ in diameter out of 24 to 30 gauge galvanized – in seconds, not minutes and with only one pass! Just c...
TK Hem & Kick Roll Former
- Manufacturer: Tin Knocker
This machine is standard equipped with no tooling in the center position and (2) sets of outboard shafts equipped with; ½” x 180-degree hem rolls for 20-26ga (right side) ½ Hem with 5/8” Kick Rolls (left side) See .
TK 20 Ga. Pitts. (With Choice of Drive Cleat or Acme Rolls)
- Manufacturer: Acme
. This 5 station 20 Gauge Pittsburgh lock roll former is offered with choice of Drive Cleat or Acme Rolls on the other outboard side. Powered by a 1 HP motor with V-belt drive, this machine is built for dependab...
Sutton, MA
TK 20 Ga. Button Lock (230/3 Phase) (3 HP)
(Also known as “Button Punch Snap Lock” Tin Knocker’s 9 Station Button Lock Roll Former means no hammering over of edges and fast duct assembly. 220/3/60 Electrics, standard. Comes with “male” tooling on one sid...
- Sutton, MA
RAMS-2013 S & Drive Machine
- Manufacturer: Rams
The unit comes with a 3 HP electric motor, 208-230V single phase .We use Torrington Needle Bearings and hardened steel components throughout (62 Rockwell). The cabinet is heavy gauge steel with a Hammertone Green...
Sutton, MA
RAMS-2007-AA Auto Guide 20ga Stand Alone Power Flanger
- Manufacturer: Rams
model: Capacity | rams-2007-aa: 20-24 Gauge Mild Steel
Sutton, MA
RAMS 2060-DB 60″ 20 Gauge Duct Beader
- Manufacturer: Rams
Sutton, MA
CR8-SDC Rollformer
- Manufacturer: SDC
Ductformer’s CR8-SDC Rollformer has both versatility and flexibility. Altogether the Multiple Roll Tooling configurations that are available on the CR8 including Slip and Drive Cleats, Male and Female Snap-Lock, ...
Sutton, MARAMS 24-28 Pittsburgh Machine
- Manufacturer: Rams
The unit comes with a 1/2 H.P. electric motor, 115/208-230V, 5.4 AMPS 60 cycle single phase. We use Torrington Needle Bearings and hardened steel components throughout, 62 Rockwell. This unit features outboard sh...
Sutton, MA
