Used working in doitsu

Gas Powered Air Compressor: Arteer, 15hp, 175psi working pressure, 1 cylinder, 420cc engine, Does have Damage on Belt Shroud and Air Cleaner

Unused Gas Powered Air Compressor: Arteer, 15hp, 175psi working pressure, 1 cylinder, 420cc engine

HFA 2200 Series 16"W x 17' 4" Incline Drying Conveyor 120V Torn Belt Bad Fans

• Manufacturer: HFA

Bed Height (From Floor): Conveyor is on adjustable t-slot frame and legs. 28"-60" on infeed. 116" max at the top. Has angle adjustment on both legs. Voltage tested and wired for:: 115V Product Videos If this item...

KleenLine 14.5ft Dual Belt Stainless Steel Flat Conveyor

• Manufacturer: Correa

Unit is USED. The unit was removed from a working environment and was functioning as intended when removed from service. The unit shows some signs of wear, but none effecting the intended use of the unit. Air cyl...

Dematic 42"x 27' Flat to Incline Belt Conveyor LH Center Drive 460V 216fpm 115"H

• Manufacturer: Correa

Slider bed infeed to belt-over roller incline section. Motor & Gearbox: 1Hp 230/460V 3PH Motor 10:1 Gearbox Bed Height (From Floor): Current set up: 40"-43 Infeed. 115" Discharge top of bed. This is the minimum h...

Ryson 1300-400-B1 Elevating Spiral Conveyor 16" Slat Belt 2Hp 230/460V 15' 4"H

• Manufacturer: Ryson

Ryson Model 1300-400-B1-5.25. Serial 143688-2 Bed Height (From Floor): Infeed 34" to 38" Top of discharge belt is 15' 4" with legs at minimum height. Conveyor legs are 20" to 24" height with leveling screws...

Ryson 1300-400-B3 Elevating Spiral Conveyor 16" Slat Belt 2Hp 230/460V 3PH 14'H

• Manufacturer: Ryson

Ryson Model 1300-400-B3 4 1/4. Serial 184720. Bed Height (From Floor): Infeed 34" to 38" Top of discharge belt is 14' with legs at miniumum height. Conveyor legs are 20" to 24" height with leveling screws. ...

Roach 18"x 24"L Small Slider Bed Conveyor 12" Belt .5Hp 230/460V 3PH 80 FPM

• Manufacturer: Roach

We set up and test all our conveyors before listing. Motor & Gearbox: 1/2Hp 230/460V 3PH 25:1 Gearbox Voltage motor is currently wired for:: 460V 3PH If this item ships as Flat Rate Freight please see details in ...

47"W MatTop Roller Belt Conveyor 44"BF 42"Belt 15Hp 3PH 79' + 83' Lot of 2

This is a lot of 2 separate conveyors with the same size drives. 79' and 83' lengths with 2 different leg heights. Motor & Gearbox: 15Hp 230/460V motor with 9:1 gearbox. Bed Length: 79' & 83' Lengths. 79' conve...

Dematic 39"x 10' Gapper Conveyor 34" Belt 2-Speed Package Gapping 90/165fpm

• Manufacturer: Correa

Note: Unit has transition roller shown in images, but is not included Motor & Gearbox: 1Hp 230/460V 3PH 30:1 Gearbox. Voltage tested and wired for:: 460V If this item ships as Flat Rate Freight please see details...

Dryer-Flaker Drum and Belt 300 mm (11.8 in) - IPP# 704614

• Manufacturer: R.Simon Dryers

face chrome plated single drum flaker/dryer Drum working pressure 5.5 bar, speed 3 to 21 rpm, cored for steam/hot oil heating

Dorner 2200 Series 12"x 10' Incline Belt Conveyor 115V Variable Speed 114FPM

• Manufacturer: Dorner

Dorner aluminum conveyor on steel adjustable leg supports. Motor & Gearbox: 10:1 Bodine DC gearmotor 130V 1/3Hp. Bed Height (From Floor): Lowest height is 9" Infeed to 35" at top. Highest setting is 7" Infeed 5...

Roach 33"x 36" Slider Bed Conveyor 27" Belt .5Hp 230/460V 3PH End Drive 55 FPM

• Manufacturer: Correa

Motor & Gearbox: 1/2Hp 230/460V 3PH 30:1 Gearbox If this item ships as Flat Rate Freight please see details in Shipping tab

New London Engineering 21"x 10' Incline Conveyor 12" Cleated Belt .5Hp 3PH 25FPM

• Manufacturer: New London Engineering

Motor & Gearbox: 1/2Hp 1750 RPM 230/460V 3PH Motor 60:1 Gearbox Bed Height (From Floor): Infeed: 31" min to 52" Max. Discharge: 45" to 58" Current Height is 31" at low end, 56" at top. Bracing will need remov...