- Trusted Seller
Bronco Sand Blasting Hanging Spinner Machine Blast Shot Blast 1-3 Station Finishing Machines
- Manufacturer: Spinner
“In excellent condition. Very low hours; little use. Meter reads approx. 5,200 hours.” Bronco shot blast equipment is used to clean metal castings, heat treated parts, structural steel, fabrications and forgings....
- Trusted Seller
#4 ACT22 5/8 x 5/8
- Manufacturer: Giant Finishing
#4 is an extremely aggressive aluminum oxide based ceramic media. Removes stubborn burrs and breaks edges quickly, with a moderate wear rate. 105LBS/ Cu. Ft.
Addison, TX - Trusted Seller
40S ACT45 3/8" X 1/4"
- Manufacturer: Giant Finishing
40S is a silicon carbide based media, it is an extremely fast cutting, ceramic media that provides a fine finish with maximum metal removal in a minimal amount of time. It can be used where brown fused aluminum o...
Addison, TX - Trusted Seller
XFC ACT 7/8 x 7/8
- Manufacturer: Giant Finishing
XFC media is designed for fast metal removal, and surface improvements. Matte finish and moderate wear rate but will reduce cycle time and improve efficiency. 85-90 LBS/cu ft
Addison, TX - Trusted Seller
MC ACC 7/8" X 1-1/2"
- Manufacturer: TBT
MC is a coarse grain aluminum oxide, ceramic media providing an excellent cut to wear ratio. Its metal cut to media wear ratio makes it a very efficient media, suitable for a wide variety of applications. (90 lbs...
Addison, TX - Trusted Seller
120C Cone 1-1/8" X 1-1/8"
- Manufacturer: Giant Finishing
120C is the abrasive version of our high-density 120 formula. 120C is a long- wearing formula with excellent metal cut. It is typically used on tough aerospace alloys such as titanium. 120-125 LBS/Cu. Ft.
Addison, TX - Trusted Seller
FFP Cone 3/8"
- Manufacturer: Giant Finishing
Take your finish to a whole new level with this light weight pre plate media. Extremely long lasting, this media was designed to put extremely fin finishes on your parts. 60-65 LBS/ Cu. Ft.
Addison, TX - Trusted Seller
MC ACT20 5/8" X 5/8"
- Manufacturer: Giant Finishing
MC is a coarse grain aluminum oxide, ceramic media providing an excellent cut to wear ratio. Its metal cut to media wear ratio makes it a very efficient media, suitable for a wide variety of applications. (90 lbs...
Addison, TX - Trusted Seller
BV Wedge 1.5"
- Manufacturer: TBT
BV comp is a fast cut aluminum oxide based ceramic media. Removes stubborn burrs and breaks edges quickly, with a good wear rate. 95LBS/ Cu. Ft.
Addison, TX - Trusted Seller
#4 ACT22 7/8 x 7/8
- Manufacturer: Giant Finishing
#4 is an extremely aggressive aluminum oxide based ceramic media. Removes stubborn burrs and breaks edges quickly, with a moderate wear rate. 105LBS/ Cu. Ft.
Addison, TX - Trusted Seller
120C ACT20 3/8" X 3/8"
- Manufacturer: TBT
120C is the abrasive version of our high-density 120 formula. (120-125 lbs. /cubic foot, color: dark brown. 120C is a long- wearing formula with excellent metal cut. It is typically used on tough aerospace alloy...
Addison, TX - Trusted Seller
SY-I CONE 3/4"
- Manufacturer: TBT
Light weight, fast cutting media that leaves excellent finish ready for anodizing or painting. This media is very comparable to our OM plastic media; COLOR: Tan; WEIGHT: 55-60 lbs.
$60 USDAddison, TX - Trusted Seller
XFC ACT 1-7/8" x 5/8
- Manufacturer: TBT
XFC media is designed for fast metal removal, and surface improvements. Matte finish and moderate wear rate but will reduce cycle time and improve efficiency. 85-90 LBS/cu ft
Addison, TX - Trusted Seller
XFC ACT 5/8" X 5/8"
- Manufacturer: TBT
XFC media is designed for fast metal removal, and surface improvements. Matte finish and moderate wear rate but will reduce cycle time and improve efficiency. 85-90 LBS/cu ft
Addison, TX - Trusted Seller
#4 ACT22 3/8 x 3/8
- Manufacturer: Giant Finishing
#4 is an extremely aggressive aluminum oxide based ceramic media. Removes stubborn burrs and breaks edges quickly, with a moderate wear rate. 105LBS/ Cu. Ft.
Addison, TX
Tip: Enter manufacturer, model or keyword
