Used processing

3.5″ TWO STAGE EXTRUDER SCREW 12026

3.5″ two stage chrome plated extruder screw, approximately 24:1 L/D, dual mixing section and dual key shaft.

DAVIS STANDARD 3.5″ SINGLE STAGE 12028

• Manufacturer: Davis-Standard

Davis Standard 3.5″ chrome plated single stage extruder screw. Approximately 24:1 L/D. Four rows of mixing pins.

CLOEREN 3-WAY CO-EX BLOCK 14423

Cloeren 3-way co-ex block for 2.5″, 3.5″, and 5.25″ extruders. Manufactured in 2000. Never been used.Two units are available.

HOMEMADE CRAMMER FEEDER 11024

Homemade crammer feeder belt driven auger by a 5HP 180-Volt 1,750 RPM DC motor through a gearbox approximately 30″ diameter hopper with 40″ long cone. 25:1 gearbox ratio for 4.5″ extruder heavy duty auger protrud...

HESTON 6″ SCREEN CHANGER 2709

6″ Heston screen changer, no model or serial number. 6″ diameter fits HPM extruder, with 3HP pump.

CLOEREN 12″, 3 LAYER VANE 10872

Cloeren 12″ 3 layer vane die, S/N D.ND935-0103-01, job no. 91-935, mounted on a caster stand, three 1.5″ material entries on a Cloeren 3 layer co-ex block (a b c), job no. D-935-2001-01, S/N E-3lSP-1636, 0.001″ t...

EDI 28.5″ ULTRAFLEX H40 SHEET 6671

• Manufacturer: EDI

Extrusion Dies, Inc. 28.5″ Ultraflex H40 sheet die. S/N 89-12354. 0.001″ – 0.040″ lip opening 240 volt 350 watt heaters 1.25″ diameter rear material entry. Manufactured 4/89. 990 Lbs. mounted on 41″ centerline v-...

EDI 36″ SHEET DIE 2859

• Manufacturer: EDI

EDI Autoflex 36″ sheet die, S/N 859445. Rebuilt. 230-Volt with 3/4″ back center feed. Mounted on a stand.

EDI 89″ ULTRAFLEX H75 SHEET 12204

• Manufacturer: EDI

Extrusion Dies, Inc. 89″ Ultraflex H75 sheet extrusion die. S/N 00-21282. Manufactured in March of 2000. Lip opening dimensions are 0.01″ – 0.075″ with a 0.300″ lip land length. All flow surfaces are UltraChrome ...

KAYENESS GALAXY III 9052 CAPILLARY 14779

Kayeness Galaxy III model 9052 capillary rheometer, 4.5″ travel. Touch pad controls, on mount pads, in excellent condition.

WIRE COAT EXTRUSION DIE WITH 10650

Co-ex wire coating extrusion die, manufacturer unknown. 240-Volt heater bands, 1 3/4″ material entry.A possible application for this die would be wire insulation with a clear coat over the wire on the co-ex side ...

LEISTRITZ 27MM TWIN SCREW EXTRUDER 18970

• Manufacturer: Leistritz

Used Leistritz Twin Screw Extruder, Type MIC 27-GL-36D. (2) 1.05″ (27 mm) diameter screws. 36:1 L/D Ratio. Co-rotating. 8 barrel housing section electrically heated, water cooled. (1) Degassing port. Maximum scre...

KRYENBORG 4.5″ CONTINUOUS SCREEN CHANGER 18956

Used 4.5″ (121mm) Kryenborg continuous screen changer, model K-SWE-121, dual 4.5″ breaker plates, rated 200-500 kg/hr, on cart. With hydraulic pump

EREMA PC1007T FILM RECLAMATION LINE 18886

• Manufacturer: Erema

2012 Erema model PC1007T film reclaim lineS/N P11/232. Rated at 350-430 kgs/hour on LDPE and LLDPE and 300 kgs/hour on HDPE. line consists of the following:Model FB6000/900 inclined cleated in-feed conveyor measu...

3.5″ STATIC MIXER 18860

Used 3.5″ static mixer. 24″ long. 10″ OD flanged and threaded with 3.5″ inlet and 2.5″ OD opening. 9″ OD flange with 2.5″ opening.