Used processing

Trusted Seller
GALA 403VDW
- Manufacturer: GALA
Used 50,000 Lb. Per Hour Gala Model 403VDW Stainless Steel Spin Dryer 43" diameter circular housing 20 hp Baldor motor Serial No. 911039-2
Hainesport, NJ
Trusted Seller
AIR KNIFE 6"
- Manufacturer: AIR KNIFE
Used 6" Wide Air Knife With 2 HP Blower
Hainesport, NJ
Trusted Seller
Cincinnati CMT80L-APC
- Manufacturer: Cincinnati
- Model: CMT
Used Cincinnati model CMT80L-APC conical counter rotating twin screw plastic extruder. Screw length approximately 1,665mm long x 80mm diameter at the discharge. Has adaptor plate that reduces the barrel exit down...
Hainesport, NJ
Trusted Seller
BATTENFELD-CINCINNATI CM55
- Manufacturer: Battenfeld-Cincinnati
Used Battenfeld-Cincinnati model CM55 counter rotating approximately 55mm diameter twin screw extruder. Conical screw design. Barrel is electrically heated and air cooled in three zones with air blowers with 0.20...
Hainesport, NJ
Trusted Seller
FARRIS 8550F
- Manufacturer: Farris
Used Farris 12" Wide x 30" Long Solid Belt Puller Manufacturer: Farris Model: 8550F Has manual belt adjustment, and variable speed transmission Rated 3-50 feet per minute
Hainesport, NJ
Trusted Seller
GOODMAN 3" Wide x 22" Long
- Manufacturer: GOODMAN
Used Goodman Solid Belt Puller – Approx. 3" (76 mm) Wide x 22" (559 mm) Long Solid belt design with an approximate belt width of 3 inches (76 mm) and length of 22 inches (559 mm). Frame includes a provision for i...
Hainesport, NJ
Trusted Seller
GALA 16.2ECLN-BF
- Manufacturer: GALA
Used Gala Stainless Steel Spin Dryer Model 16.2ECLN-BF Serial #982157
Hainesport, NJ
Trusted Seller
AMERICAN MAPLAN V2-125-V/2L
- Manufacturer: Maplan
Used Battenfeld vacuum/cooling tank. Type V2-125-V/2L, serial #83-4058-67-01. Has 14" x 14" cross section x 18' long chamber with 10" opening. Includes (1) vacuum pump and (2) water pumps. (1) vacuum pump missing...
Hainesport, NJ
Trusted Seller
RANDCASTLE Ø51 мм × 203 мм
- Manufacturer: RANDCASTLE
Used 2" O.D. x 8" Wide Randcastle Sheet Extrusion 3-Roll Stack including Pull Roll Station and Single Position Winder.
Hainesport, NJ
Trusted Seller
1991 DAVIS STANDARD 4.5"
- Manufacturer: Davis-Standard
Used 4.5" Davis Standard 30/1 L/D Extruder, Electrically Heated Air Cooled Barrel. Includes gearbox with 17.36/1 gear ratio rated at 321 hp. Serial #M-3315, SO #05432. New 10/1991. Includes Kryenborg Type K-SWE-1...
Hainesport, NJ
Trusted Seller
1997 DAVIS STANDARD 5.11"
- Manufacturer: Davis-Standard
Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...
Hainesport, NJ
Trusted Seller
2000 DAVIS STANDARD 5.11"
- Manufacturer: Davis-Standard
Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...
Hainesport, NJ
Trusted Seller
2008 COPERION ZSK-40-MEGA
- Manufacturer: Coperion Waeschle
Used 40mm Coperion Mega 40 co-rotating twin screw extruder. New 2008. No barrels or screws included. Driven by 200 hp AC motor, 1790 rpm, with Powerflight VFD controller. Has 1.155 gear ratio supplying 1200 rpm s...
Hainesport, NJ
Trusted Seller
2004 SAKAS
- Manufacturer: SAKAS
Used 36" Wide Sakas Traveling Cut Off Saw Including 42" Wide Belt Take-Away. New 2004. Saw Model GS36.
Hainesport, NJ
Trusted Seller
MARSHALL & WILLIAMS CO-EX SHEET EXTRUSION LINE
- Manufacturer: Marshall
Used Marshall & Williams Co-Ex Sheet Extrusion Line Consisting of the Following: 2.5" Welex 36/1 L/D with air cooled vented barrel, with 9.145/1 gearbox ratio including manual screen changer, water cooled screw a...
Hainesport, NJ