Used processing in Illinois, USA

EDI 36″ SHEET DIE 2859

• Manufacturer: EDI

EDI Autoflex 36″ sheet die, S/N 859445. Rebuilt. 230-Volt with 3/4″ back center feed. Mounted on a stand.

EDI 89″ ULTRAFLEX H75 SHEET 12204

• Manufacturer: EDI

Extrusion Dies, Inc. 89″ Ultraflex H75 sheet extrusion die. S/N 00-21282. Manufactured in March of 2000. Lip opening dimensions are 0.01″ – 0.075″ with a 0.300″ lip land length. All flow surfaces are UltraChrome ...

KAYENESS GALAXY III 9052 CAPILLARY 14779

Kayeness Galaxy III model 9052 capillary rheometer, 4.5″ travel. Touch pad controls, on mount pads, in excellent condition.

WIRE COAT EXTRUSION DIE WITH 10650

Co-ex wire coating extrusion die, manufacturer unknown. 240-Volt heater bands, 1 3/4″ material entry.A possible application for this die would be wire insulation with a clear coat over the wire on the co-ex side ...

LEISTRITZ 27MM TWIN SCREW EXTRUDER 18970

• Manufacturer: Leistritz

Used Leistritz Twin Screw Extruder, Type MIC 27-GL-36D. (2) 1.05″ (27 mm) diameter screws. 36:1 L/D Ratio. Co-rotating. 8 barrel housing section electrically heated, water cooled. (1) Degassing port. Maximum scre...

KRYENBORG 4.5″ CONTINUOUS SCREEN CHANGER 18956

Used 4.5″ (121mm) Kryenborg continuous screen changer, model K-SWE-121, dual 4.5″ breaker plates, rated 200-500 kg/hr, on cart. With hydraulic pump

EREMA PC1007T FILM RECLAMATION LINE 18886

• Manufacturer: Erema

2012 Erema model PC1007T film reclaim lineS/N P11/232. Rated at 350-430 kgs/hour on LDPE and LLDPE and 300 kgs/hour on HDPE. line consists of the following:Model FB6000/900 inclined cleated in-feed conveyor measu...

3.5″ STATIC MIXER 18860

Used 3.5″ static mixer. 24″ long. 10″ OD flanged and threaded with 3.5″ inlet and 2.5″ OD opening. 9″ OD flange with 2.5″ opening.

DYNISCO 60 HP MELT PUMP 18829

• Manufacturer: Dynisco

One used Dynisco model MSDP-430 melt pump. S/N M54343035. last used with 8″ 900 HP extruder. Includes 60 HP 480-VOLT Blue Max A/C inverter duty motor, gearbox, stand, and static mixer

JOHNSON 54 X 8 PULL 18800

• Manufacturer: Johnson

Johnson roll pull roll stand. Two (2) 54″ x 8″ diameter rubber covered rolls. Rolls are driven by an approximate 10 HP D/C motor through a “Drive-All” four speed gearbox. Air actuated top pull roll.

UN 14 ZONE EXTRUDER TEMPERATURE 18779

One (1) unused extruder temperature control panel consisting of fourteen zones of Eurotherm 2216E temp controls. Was set up for use with a 4.5″ 32:1 Gloucester extruder. Labeled for 5 extruder zones, 1 screen cha...

STERLING 6005FD-EZAC 5 HP BLOWER 18773

• Manufacturer: Sterling

Sterling model 6005FD-EZAC blower. S/N 79380. Directly driven impeller by a 5 H 230/460-volt motor. Has hinged door for easy impeller change out. 6″ OD inlet and outlet with Kongskilde OK160 rolled flange weld a...

CLOEREN 70″ AUTOFLEX SHEET DIE 18753

One (1) Cloeren 70″ auto-flex sheet die. 1″ x 4″ back center feed entrance. S/N 77831-2129. Manufactured April, 2003.

DYNISCO EH-60 6″ SCREEN CHANGER 18751

• Manufacturer: Dynisco

One (1) Dynisco model EH-60 screen changer having two nominal 6″ diameter breaker plates.

WELEX / MAAG 20 HP 18672

• Manufacturer: Welex

Welex / Maag model 56/56 20 HP melt pump with drive