Used processing in Illinois, USA

GLOUCESTER 6″ EXTRUDER 12088

Gloucester 6″ extruder. No model number and no serial number. 30:1 L/D electrically heated water cooled 6 zone vented barrel with screw and clamp. No motor. 42″ center line 1HP 6″ x 11″ oval in-feed bridge breake...

UNK MFG 5″ SINGLE SCREW 12404

Unk Mfg. 5″ single screw extruder barrel, non-vented, 24:1 L/D, 8 bolt flange mount to gearbox. Threaded front of barrel to accept screen changer. Overall length is 134.5″ with 4.25″ end extension.

DAVIS STANDARD 3.5″ DOUBLE SPIRAL 12398

• Manufacturer: Davis-Standard

Davis Standard 3.5″ double spiral screw 32:1 L/D, 136″ overall length 12″ shank.Three are available.

WELEX 6″ EXTRUDER SCREW 12347

• Manufacturer: Welex

Welex 6″ extruder screw, S/N JF05444-000, 32:1 L/D, 2 stage, 216″ overall length.

6″ WELEX EXTRUDER SCREW 12350

• Manufacturer: Welex

6″ Welex extruder screw, S/N 144812, 32:1 L/D, 2 stage 216″ overall length. 9″ long x 1.5″ wide keyway.

TWO STAGE 4.5″ CHROME PLATED 12019

4.5″ chrome plated two stage extruder screw with mixing pins at the end of first stage. Approximately 28:1 L/D single key shaft. Unknown manufacturer.

DAVIS STANDARD SINGLE STAGE EXTRUDER 12020

• Manufacturer: Davis-Standard

4.5″ Davis Standard single stage extruder screw. Approximately 28:1 L/D with mixing pins at screw end.

3.5″ TWO STAGE EXTRUDER SCREW 12025

Two stage 3.5″ chrome plated extruder screw, approximately 24:1 L/D, dual mixing section and dual key shaft, unknown manufacturer.

3.5″ TWO STAGE EXTRUDER SCREW 12026

3.5″ two stage chrome plated extruder screw, approximately 24:1 L/D, dual mixing section and dual key shaft.

DAVIS STANDARD 3.5″ SINGLE STAGE 12028

• Manufacturer: Davis-Standard

Davis Standard 3.5″ chrome plated single stage extruder screw. Approximately 24:1 L/D. Four rows of mixing pins.

CLOEREN 3-WAY CO-EX BLOCK 14423

Cloeren 3-way co-ex block for 2.5″, 3.5″, and 5.25″ extruders. Manufactured in 2000. Never been used.Two units are available.

HOMEMADE CRAMMER FEEDER 11024

Homemade crammer feeder belt driven auger by a 5HP 180-Volt 1,750 RPM DC motor through a gearbox approximately 30″ diameter hopper with 40″ long cone. 25:1 gearbox ratio for 4.5″ extruder heavy duty auger protrud...

HESTON 6″ SCREEN CHANGER 2709

6″ Heston screen changer, no model or serial number. 6″ diameter fits HPM extruder, with 3HP pump.

CLOEREN 12″, 3 LAYER VANE 10872

Cloeren 12″ 3 layer vane die, S/N D.ND935-0103-01, job no. 91-935, mounted on a caster stand, three 1.5″ material entries on a Cloeren 3 layer co-ex block (a b c), job no. D-935-2001-01, S/N E-3lSP-1636, 0.001″ t...

EDI 28.5″ ULTRAFLEX H40 SHEET 6671

• Manufacturer: EDI

Extrusion Dies, Inc. 28.5″ Ultraflex H40 sheet die. S/N 89-12354. 0.001″ – 0.040″ lip opening 240 volt 350 watt heaters 1.25″ diameter rear material entry. Manufactured 4/89. 990 Lbs. mounted on 41″ centerline v-...