Used Extruders in Illinois, USA

DELTAPLAST 30MM 5 HP EXTRUDER 18678

One {1) used Deltaplast model D30:24:R 30mm extruder. S/N WO.29:79. Having a 24:1 L/D ratio at a 40.5″ centerline height. Unit has two (2) zone electrically heated, air cooled, non-vented barrel. Hamilton gearbox...

2″ PRODEX 24:1 EXTRUDER 16902

Prodex 2″ 24:1 L/D extruder. Unit has an electrically heated air cooled non-vented barrel at approximately a 48″ center-line height. Gearbox is a link-belt model EX-1028-59 has a reduction ratio of 11.36:1 and is...

DELTAPLAST 5 HP PEDESTAL EXTRUDER 18675

One (1) used 30mm Deltaplast model DVH 30.125:24 pedestal extruder. S/N WO281:1.91. Having a 24:1 L/D ratio. Unit has a three (3) zone electrically heated, air cooled, and non-vented barrel. Radicon (David Brown)...

DAVIS STANDARD 15INDS20 1.5″ EXTRUDER 12754

• Manufacturer: Davis-Standard

Davis standard model 15INDS20 1.5″ extruder S/N K-9754. SO# 02359. 24:1 L/D. Powered by a fan cooled 15 HP 500-Volt 1750/2300 RPM DC motor through a 6.53:1 gearbox 152 RPM screw speed. Electrically heated and fan...

WAYNE MFG 3/4″ EXTRUDER 17885

• Manufacturer: Wayne

One used 3/4″ 20:1 L/D Wayne laboratory extruder having a two (2) zone electrically heated, air cooled barrel. Gearbox is belt driven by a 2 HP DC Motor with controls. Unitized temperature control panel with thre...

DAVIS STANDARD 3.5″ EXTRUDER W/DUAL 17744

• Manufacturer: Davis-Standard

Davis Standard straw/tubing co-extrusion extrusion package manufactured 10/2012Last used on three color straws extruding two lanes of straws at one time. Extruders and controls are unitized on a single base. 460/...

KILLION 1.5″ 24:1 EXTRUDER SCREW 17747

Killion 1.5″ 24:1 L/D single stage extruder screw6 Available

2.5″ 30:1 L/D EXTRUDER 17759

Unknown manufacture 2.5″ extruder, 30:1 L/D air cooled non-vented barrel at a 23.5″ centerline. Powered by a 40 HP 230/460-volt A/C motor with Teco A510 inverter. 4″ x 6″ feed throat. Unitized control panel with ...

3.5″, EXTRUDER SCREW, 30:1 L/D 14756

3.5″ 30:1 extruder screw barrier mid-section, Previously ran PEP material.

GLOUCESTER 3.5″ 32:1 L/D EXTRUDER 18364

One (1) Used Gloucester model 35250R2 3.5” 32:1 L/D extruder. S/N 36736/11. Having an electrically heated, air cooled, and non-vented barrel at approximately a 65” center line height. Barrel is set up for Contra-...

GLOUCESTER 3.5″ 32:1 L/D EXTRUDER 18365

One (1) Used Gloucester model 35250R2 3.5″ 32:1 extruder having an electrically heated, air cooled, vented, and plugged barrel at approximately a 65″ center line height. S/N 36736/12. Barrel is set up for Contra-...

HPM 3.5″ 30:1 L/D EXTRUDER 17578

One (1) used 3.5″30:1 HPM extruder having an electrically heated water cooled (closed loop) vented and plugged barrel at a 51 ½” centerline height. Koellmann gearbox is driven by a 100 HP D/C motor with a Eurothe...

PRODEX 4.5″ 32:1 L/D EXTRUDER 18180

One (1) used Prodex 4.5″ 32:1 L/D extruder having an electrically heated, water cooled (closed loop), and side vented barrel. The gearbox is a Lufkin change gear type gearbox and is direct driven in a tuck under ...

WAYNE 1.250″ 30:1 L/D EXTRUDER 16355

• Manufacturer: Wayne

Wayne 1.25″ extruder, S/N 9414-832. 30:1 L/D electrically heated, air cooled, vented (venting is plugged), barrel driven by a 7.5HP DC motor with SCR control 230-Volts input power. Includes track wheel base and a...