Used Extruders in Illinois, USA

PRODUCTION COMPONENTS 54″ WIDE SHEET 16643

Production Components heavy body sheet die. 54″ wide opening with an adjustable upper lip and a fixed lower lip. 1″ back center feed set up for five (5) zones of temperature control. Unit has heat fins with cooli...

LCI ES36/36 MELT PUMP 16456

Used 5HP LCI melt pump model ES36/36, S/N 1638. LCI SO# 40-25586. Includes operator control with Reliance model GV3000 AC drive. 460v/3ph/60Hz operation. Pump is driven by a 5HP, 230/460-Volt AC motor direct conn...

PROCESSING TECHNOLOGIES 50″ WIDE 3 6522

Processing Technologies, Inc. model 5024, 3 roll down stack. S/N 297-CRS. Manufactured in February, 2000. Has two (2) 24″ diameter x 50″ wide lower chrome rolls. Upper roll is 12″ x 50″. All chrome rolls are core...

CLOEREN 12″, 3 LAYER VANE 10872

Cloeren 12″ 3 layer vane die, S/N D.ND935-0103-01, job no. 91-935, mounted on a caster stand, three 1.5″ material entries on a Cloeren 3 layer co-ex block (a b c), job no. D-935-2001-01, S/N E-3lSP-1636, 0.001″ t...

EDI 28.5″ ULTRAFLEX H40 SHEET 6671

• Manufacturer: EDI

Extrusion Dies, Inc. 28.5″ Ultraflex H40 sheet die. S/N 89-12354. 0.001″ – 0.040″ lip opening 240 volt 350 watt heaters 1.25″ diameter rear material entry. Manufactured 4/89. 990 Lbs. mounted on 41″ centerline v-...

EDI 36″ SHEET DIE 2859

• Manufacturer: EDI

EDI Autoflex 36″ sheet die, S/N 859445. Rebuilt. 230-Volt with 3/4″ back center feed. Mounted on a stand.

EDI 89″ ULTRAFLEX H75 SHEET 12204

• Manufacturer: EDI

Extrusion Dies, Inc. 89″ Ultraflex H75 sheet extrusion die. S/N 00-21282. Manufactured in March of 2000. Lip opening dimensions are 0.01″ – 0.075″ with a 0.300″ lip land length. All flow surfaces are UltraChrome ...

KAYENESS GALAXY III 9052 CAPILLARY 14779

Kayeness Galaxy III model 9052 capillary rheometer, 4.5″ travel. Touch pad controls, on mount pads, in excellent condition.

WIRE COAT EXTRUSION DIE WITH 10650

Co-ex wire coating extrusion die, manufacturer unknown. 240-Volt heater bands, 1 3/4″ material entry.A possible application for this die would be wire insulation with a clear coat over the wire on the co-ex side ...

KRYENBORG 4.5″ CONTINUOUS SCREEN CHANGER 18956

Used 4.5″ (121mm) Kryenborg continuous screen changer, model K-SWE-121, dual 4.5″ breaker plates, rated 200-500 kg/hr, on cart. With hydraulic pump

3.5″ STATIC MIXER 18860

Used 3.5″ static mixer. 24″ long. 10″ OD flanged and threaded with 3.5″ inlet and 2.5″ OD opening. 9″ OD flange with 2.5″ opening.

JOHNSON 54 X 8 PULL 18800

• Manufacturer: Johnson

Johnson roll pull roll stand. Two (2) 54″ x 8″ diameter rubber covered rolls. Rolls are driven by an approximate 10 HP D/C motor through a “Drive-All” four speed gearbox. Air actuated top pull roll.

STERLING 6005FD-EZAC 5 HP BLOWER 18773

• Manufacturer: Sterling

Sterling model 6005FD-EZAC blower. S/N 79380. Directly driven impeller by a 5 H 230/460-volt motor. Has hinged door for easy impeller change out. 6″ OD inlet and outlet with Kongskilde OK160 rolled flange weld a...

CLOEREN 70″ AUTOFLEX SHEET DIE 18753

One (1) Cloeren 70″ auto-flex sheet die. 1″ x 4″ back center feed entrance. S/N 77831-2129. Manufactured April, 2003.

DYNISCO EH-60 6″ SCREEN CHANGER 18751

• Manufacturer: Dynisco

One (1) Dynisco model EH-60 screen changer having two nominal 6″ diameter breaker plates.