Used Processing in Kentucky, USA

Trusted Seller
MITSUBISHI Plastic Injection Molding Machine Barrel Zone Heating Control Power
- used
- Manufacturer: Mitsubishi
“Pulled from working Mitsubishi Molding Machine” MITSUBISHI Plastic Injection Molding Machine Barrel Zone Heating Control Power Supply Board INV# P-1327
$200 USD
Henderson, KY
Trusted Seller
Conair 10721301 Dryer Input/Output Board - Free Shipping
- used
- Manufacturer: Conair
🔥Conair 10721301 Dryer Input/Output Board - Free Shipping INV# P-1517
$350 USD
Henderson, KY
Trusted Seller
(NEW) VAN DORN Barrel End Cap 350 Ton Plastic Injection Molding Machine
- new
- Manufacturer: Van Dorn Demag
🔥 (NEW) VAN DORN Barrel End Cap 350 Ton Plastic Injection Molding Machine 15 Holes. Female Thread for the Nozzle is about 60mm. About 5-5/8" Diameter NOTE: We think this is for a 350 Ton Press. Ask all questions ...
$500 USD
Henderson, KY
Trusted Seller
6" Diameter Taisel Kogyo Industrial Heat Exchanger Model FCF-216-2 R-2323
- used
- Manufacturer: American
“Pulled from machine with low hours” Taisel Kogyo Industrial Heat Exchanger Model FCF-216-2 R-2323 About 12" Long by 6" in Diameter ITM# P-177
$500 USD
Henderson, KY
Trusted Seller
(TESTED) MITSUBISHI PLCS-10 OPERATOR PANEL INJECTION MOLDING MACHINE
- used
- Manufacturer: Mitsubishi
“Pulled from working machine” 🔥(TESTED) MITSUBISHI PLCS-10 OPERATOR PANEL INJECTION MOLDING MACHINE INV# P-1302
$1,000 USD
Henderson, KY
PENDU Live Rolls with measuring stops
- used
- Manufacturer: Pendu
Live rolls with 3 pop-up stops 24" apart, no drive. Slots for pop-up transfer chains. Rolls are 6-1/2" diameter and approximately 13-1/2" wide. Overall length approximately 20'.
Oneida, KY
G-Tek Flat Belt 15' x 21"
- used
- Manufacturer: G-Tek
Flat table top style product conveyor. Factory built with hydraulic motor drive. 21" wide belt approximately 15 feet long.
Oneida, KY
TABLE OF DEHUMIDIFIERS /
- used
TABLE OF DEHUMIDIFIERS / MISC
Louisville, KY
GRIEVE BF-122412-HT, BT-122012
- used
- Manufacturer: Grieve
GRIEVE OVER/UNDER FURNACE MODEL BF-122412-HT w/TEMPERING FURNACE MODEL BT-122012 460V 3 Phase 26 Amps 20 KW 26 Amps -Workspace Dimensions: upper - 12" wide x 24" deep x 12" high; lower - 12" wide x 20" deep x 12"...
$19,500 USD
Get financing
Est. $383/mo
Louisville, KY
Trusted Seller
2017 KAESER EB421C
- used
- Manufacturer: Kaeser
This blower has never been used, purchased for a project and the job was cancelled.
Louisville, KY
Trusted Seller
DONALDSON VF-150
- used
- Manufacturer: Donaldson / Torit / DCE
Aircel VF-150, 150 CFM, 115V, NEMA 4 Non-Cycling Refrigerated Air Dryer 150 CFM capacity 200 PSIG max operating pressure 100°F inlet temperature 38°F dew point Timer drain Internal high-efficiency separator R-134...
Louisville, KY
Bag House
- used
The used bag house dust collection system is an effective solution for managing dust and improving air quality in industrial environments. Although the manufacturer and specific model are unknown, this system off...
$10,000 USD
Get financing
Est. $196/mo
East Bernstadt, KY
Trusted Seller
INGERSOLL RAND HB21004HN00S
- used
- Manufacturer: Ingersoll Rand
Country: United States
Louisville, KY
Trusted Seller
CUDA H20-2840
- used
- Manufacturer: Cuda
Extra baskets Country: United States | Tank-w: 28" | Tank-h: 40" | Dimensions: 50"x51"x80" | Weight: 1000
Louisville, KY
Trusted Seller
OMEGASONICS omg-4430
- used
- Manufacturer: OMG
This machine was purchased for a job and used less than 10 times. Customer paid almost $35k new. The OMG-4430 ultrasonic cleaner is our largest, portable standard floor model at 208 gallons. 8000 Watts peak ultra...
Louisville, KY