Used sets in Taiwan

Tape Holding Power Tester (Normal Type) 10 sets Confirm to GB/T 4851, ASTM D3654, PSTC 7 Standard

• Manufacturer: cometech testing machines

QC-801(A)(B)(C) Specimen stick test area can use 1/2”x1”or 1”x1”, unified to use 0.45 pound of load scrunch through specimen, hanging counterweight in the lower end of specimen. Timer automatically stops counting...

FPC Flexible Testing Machine

• Manufacturer: cometech testing machines

QC-119 FPC Flexible Testing Machine specialized in testing the using life of flexible circuit in its motion directions to proceed with life test in usage occasions Industry: Electron

TABER Abrasion Tester Confirm to ASTM D3884, ASTM D1175, ASTM D1044, ASTM D4060, TAPPI T476, SIO 9352, ISO 5470-1, JIS K7204, JIS A1453, JIS K6902, JIS L1096, JIS K 6964, DIN 52347, DIN53109, DIN53754, DIN 53799 Standard

• Manufacturer: SIO

QC-619K is made up of one specimen clamping disk and two grinding wheels and two vacuum nozzles, specimen clamps above disk with two wheels that can select different weights on specimens, grinding wheel diameter ...

Perspiration Tester Confirm to AATCC-15, ISO 105, JIS 0848, GB T5713 Standard

• Manufacturer: cometech testing machines

QC-315 is used to determine the fastness of colored textiles soaked in water condition. Using textile and one piece (multi-fiber fabric) or two pieces (single fabric) stitched, after soaking in solution, be clamp...

Solar Panel Abrasion Tester Confirm to EN 1096-2 Standard

GI-M043 is designed for the requirements of solar panel surface abrasion test, use wool felt to do abrasion test, during testing process that each wool felt abrasion stroke needs to self-rotation 20 degrees, set ...

Optical Film Abrasion Tester

WD-M013 is mainly use in light load friction test. Specimen placed on a movable platform, abrasion head is designed to be able to zero setting of original load and test load can be set to 50-2000g. Light friction...

Screw Penetrator

• Manufacturer: cometech testing machines

YY-S20 is designed to test self-tapping screws or drilling screws penetration ability, clamping iron plate on lower fixture, set rotating speed and load, put screws and then start machine. Screw rotates to penetr...

GR-B050 90° peel grips

• Manufacturer: cometech testing machines

Capacity: 200N | Jaw face width: 5-10mm | Specimen thickness: 0.01~3mm | Temperature limits: 0~100℃ | Weight: 2200g set | Standard: ASTM D3330

Demattia Flex Crack Tester Confirm to ASTM-D813, JIS-K6301 Standard

• Manufacturer: cometech testing machines

QC-625 Rubber, leather, synthetic leather, sole of shoes, after a constant flexing bending motion, observe the cracking lever to judge and compare the endurance of material. Industry: Rubber, Leather, shoes sole

Compression & Deformation Tester Confirm to ASTM-D395, JIS K6262, GB/T 7759, ISO 815 Standard

• Manufacturer: cometech testing machines

It is use static state way to testing rubber under constant compression and exerting heat condition to check the permanently deformation rate of the material. This test needs to collocate with oven and Thickness ...

Motor Twist Counter for yarn, Manual twist counter for yarn Confirm to ISO 2061 ASTM D1422 BS-903 FZ-T10001 JIS L1095 Standard

• Manufacturer: cometech testing machines

This test machine uses the characteristics of different length of yarn after twisting. Use the pointer or sensor to detect changes in the yarn to figure the twist value of the measured object. This is a very impo...

DIN Abrasion Tester Confirm to DIN53516 ISO-4649 GB/T 9867 SATRA TM174 Standard

QC-618A is suitable for elastic material, rubber, tires, conveyor belts, transmission belts, shoe soles and software synthetic leather. The specimen of wear area is dia. 16mm which provide the required load and t...

Universal Material Tester Horizontal Type Confirm to ISO 7500-1 , JJG475-88 , ASTM E4 , DIN5122 , JIS B7721/B7733 , EN 1002-2,BS1610,GB T228 Standard

• Manufacturer: cometech testing machines

This tester is horizontal design, is especially developed for 180° peeling test and friction force horizontal tensile, it can reduce specimen self-weight to affect test force during test, machine with small volum...

Adhesion/Release Tester Confirm to FINAT 4 Standard

• Manufacturer: cometech testing machines

QC-527 test range can do low and high speed peel test and also for 90 ° 、180° multi-angle peel test. Low speed peeling force generally uses 300mm/min to proceed with test, testlow-stick adhesive label tear force....

QC-619C Abrasion Tester Confirm to ASTM D3884, ASTM D1175, ASTM D1044, ASTM D4060, TAPPI T476, SIO 9352, ISO 5470-1, JIS K7204, JIS A1453, JIS K6902, JIS L1096, JIS K 6964, DIN 52347, DIN53109, DIN53754, DIN 53799 Standard

• Manufacturer: SIO

This equipment is designed for abrasion testing of various materials such as paper, textiles, plywood, flooring, glass, rubber and plastics. The specimen is fixed on the clamping area with a corresponding fixture...