NEW SHARP SV-5128ST BOX WAY CNC VERTICAL MACHINING CENTER in Bannockburn, IL, USA
New
Doubleclick to zoom in
Contact the seller for
additional photos and information.
Specifications
- Condition
- new
- Stock number
- 14639
- Travel size (x, y, z)
- 51.2" x 27.56" x 27.95" (1300 x 700 x 710 mm)
- Table size
- 59" x 25.6" (1500 x 650 mm)
- Maximum table load
- 2200 lb. (1,000 Kg)
- Table t-slot size
- 5" x 0.7" x 3.9" ( 5 x 18 x 100 mm )
- Spindle center to column (throat)
- 28.7" ( 730 mm )
- Spindle nose to table surface
- 5.1" ~ 33" (130-840mm)
- Floor to table
- 33.5" (850 mm)
- Spindle speed (rpm)
- 5128 ST - 10,000 rpm
- Spindle taper
- CAT-40
- Spindle motor
- 20/25 HP (15/18.5 kw)
- Cutting feed rate (all axes)(max)
- 393 ipm (10,000 mm/min)
- Rapid traverse (x,y)
- 945 ipm (24,000 mm/min)
- Rapid traverse (z)
- 590 ipm (15,000 mm/min)
- Tool capacity
- 24
- Max. tool diameter
- 2.99" (76 mm)
- Without adjacent tool
- 5.9" (150 mm)
- Max. tool length
- 11.8" (300 mm)
- Max. tool weight
- 15.4 lb. ( 7 Kg)
- Tool change time, tool to tool
- 4.6 sec
- Tool change time, chip to chip
- 6 sec
- Fanuc systems, standard
- Oi-MD
- Positioning accuracy
- +/- 0.0002" (+/- 0.005 mm)
- Repeatability accuracy
- +/- 0.0001" (+/- 0.003 mm)
- General power
- 220V/ 3 phase/ 60Hz
- Air requirement (psi)
- 6 CFM @ 88psi
- Machine dimensions
- 126" x 114" x 122", ( 2,900 x 2,900 x 3,100 mm)
- Approximate weight
- 16,300 Lbs (7,400 Lg)
- Category
- Machining Centers in USA
- Subcategory
- Machining centers, vertical
- Listing ID
- 103435881
Description
NEW SHARP SV-5128ST BOX WAY CNC VERTICAL MACHINING CENTER
51.2" x 27.5" x 28” (1,300 x 700 x 710 mm ) travel, machine weight over 17,000 lbs (8,000 Kg )
Induction hardened and ground box ways (X,Y,Z) for rigidity
Meehanite cast iron is used on all structural components.
Finite Element Analysis (FEA) is used to optimize the structure for rigidity.
A wide saddle fully supports the worktable throughout the travel.
Fanuc Oi-MD control
Fanuc digital AC servo, motors and drives
CAT-40 taper spindle with 10,000 RPM, 25 HP motor with chiller
Double anchored, pre-tensioned and double nut ball screws
20 bars coolant through spindle prepped
Travel Size (X, Y, Z)
51.2" x 27.56" x 27.95" (1300 x 700 x 710 mm)
Table Size
59" x 25.6" (1500 x 650 mm)
Maximum Table Load
2200 lb. (1,000 Kg)
Table T-Slot Size
5" x 0.7" x 3.9" ( 5 x 18 x 100 mm )
Spindle Center to Column (throat)
28.7" ( 730 mm )
Spindle Nose to Table Surface
5.1" ~ 33" (130-840mm)
Floor To Table
33.5" (850 mm)
Spindle Speed (rpm)