Used compactrio controller in Belgium

2 lifting bails for small casting ladles, ± 60 kg

• Manufacturer: Kleine

Ø hole for ladles 350 mm, ladles ± 60 kg Ø ± 370/280 mm, height 390 mm Tiltable by hand Without chain hoist With 1 control for hoist

Shake out conveyor JÖST 6250 x 1620mm (frequency-controlled)

• Manufacturer: Jöst

External dimensions: Length: 6420 mm; Width: ±2000 mm (without motors); Height: 1685 mm Usable dimensions: Length: 6250 mm; Width: 1620 mm. With second vibration discharge conveyor for parts Length: 2365 mm; widt...

KUKA robot, CE

• Manufacturer: Kuka
• Model: KR 240

First arm length 1250mm Second arm length 1000mmm With control board With protective grids With roller conveyor With gripper

Dosing screw, Ø 45 mm, length 1350 mm

External dimensions: length 1850 mm, width 700 mm, height 1100 mm Engine: 0,75 kW, 220/380 V, type: drive, 1380 rpm With spare hopper, ± 100 l, rectangular Power transmission over V-belt Without control box With ...

Furan sand screw mixer BORDEN, ± 2 t/h with silo

Type: Micro 86, Serial number: 164 The mixer is hanging under the bunker External dimensions when fully mounted: 5800 mm x 2240 mm, h. 5400 mm Mixer motor UNELEC, TtypeT132M16; 4 kW; 960 rpm; 220/380 V Bunker wit...

molding line HWS-HSP1, green sand

• Manufacturer: Kleine

Weight: ± 30 000 kg construction year 1996 Dimensions: 2700 mm x 2000 mm x 2700 mmSIEMENS S5 control and control panel- 132 molding boxes 650 mm x 500 mm x 200 mm- Roller conveyors 36.5 m- Air tank for SEIATSU p...

2000 Mixing plant for core sand LÜBER 7,5t/h

• Manufacturer: Lüber

Complete installation with 2 core sand mixers Mixer capacity / filling volume: Both mixers are mobile With laterally movable weighing hopper With 1 sand silo 6m³ separated in 2 (for old and new sand) With 3 dosin...

Double-joint arm screw mixer WÖHR, 20 t/h

• Manufacturer: Wöhr

Type: WDS, serial number: 356165 Outside dimensions: 8800 mm (stretched arm) x 1700 mm (feet), h. 3700 mm Distance between entry and exit: 7000 mm ( first arm 4500 mm., second 2500 mm. ) Motor SEW, type: RF87DT80...

Semi-automatic moulding line HWS/HSP 1

Serial number: 1190, com. number: 10469 Year of construction: 1995, weight: ± 25000 kg Height 2970 mm Plant equipt by several hydraulic units With rotating table, roller stripping Stroke 200 mm, press stroke 200...

Fastloop with vibrating table

Fastloop consisting of: Vibration table: Dimensions: Length: 1000mm; Width: 1000mm; Height: 650mm roller width: 675mm; center distance: 225mm; Ø roller: 90mm With relay control 4 air bars End switch under the tab...

Cut-off machine with 2 parallel disks, Ø 300 mm, HANS BOOST

Type: STA 300/300, serial number: 354 Year of construction: 1974, weight: ± 700 kg Hydraulic tubes Motor H SAFTIG, type AOM132S-2, 7,5 kW, 380 V, 2910 rpm With table length 300 mm, width 200 mm, 2 discs Ø 300 mm ...

1997 Moulding line BELLOI & ROMAGNOLI, 650 mm x 650 mm x 200/200 mm

Type: BRAP/4, construction year: 1997 Moulding line BELLOI & ROMAGNOLI hydraulic squeeze with rotating table With: - roller conveyors for return line (11 meters long) - roll-over (manual drive) - hydraulic statio...

Moulding unit HWS/HSP1, hydraulic 500mm x 400mm

Serial number: 10502Year of construction: 1992Weight: ± 22 000 kgDimensions: 2700 mm x 2000 mm x 2700 mmPower: 400V, 50 Hz32 molding boxes = 16 pairsDimensions of boxes: 500 mm x 400 mm x 150/150 mmWith transport...

2010 FASTLOOP, plate dimensions 2500 mm x 2300 mm

• Manufacturer: SOGEMi

Fastloop with 9 plates, 2500 mm x 2300 mm (wooden plates with holes) With 5 motorisated rolling conveyors, width 1000 mm; lenght ( 1×3970mm; 3×3480mm; 1×2980mm) With 2 motorisated support roller cconveyors, width...

Double arm screw mixer IMF 30 t/h (Alphaset), with fast loop

Consisting of: -Mixer : Brand: IMF outside 5400 mm x 1600 mm, h. 4200 mm, expanded arm Length second arm, screw length between axle 2000 mm - 1 vibrating table set up on 6 pneumatic cushions, outside 2100 mm x 14...