Used Processing in British Columbia, Canada

37' MILL POWER VIBRATING CONVEYOR

• Manufacturer: Mill Power

- unbalanced - 24" wide x 37' long - c/w grizzly - metal trap c/w magnet - very good condition (never been installed)

Log Haul Conveyor

- Heavy duty trough, approximately 60' long - WD480 box chain (8" pitch x 14-1/2" wide) - Tail pulley c/w air bag tension system - No drive

39' EDEM VIBRATING CONVEYOR

- balanced - 18" wide - c/w 5' fiberglass section - c/w grizzly

23" x 25' Long Belt Conveyor

- Frame is 27' long x 38" wide x 43" high

30" x 92' Troughing Conveyor

- Truss frame construction c/w catwalk (Approx 7' wide x 4'-4" high) - Two (2) sections (47'-5" and 44'-6") - Drive assembly - Head pulley assembly - No tail pulley - Belt

HYDRO-O FLEX TRAILER DUMP

- Built in 1994 - Back on style - 65' long deck x 10" wide - 50 ton capacity - 63 degree tilt angle - Two (2) hydraulic cylinders (chrome plated) - Hydraulic Power Unit (575/3/60) - Hopper c/w twelve (12) strand ...

16' CanCar Half Taper Infeed

• Manufacturer: Canadian Mill Equipment

- Alligator chain - 2 infeed spike rolls c/w 5 HP motors - Infeed drive complete - Good condition - New spare top & bottom chain

CanCar Side Head Module

• Manufacturer: CanCar

- Side head module - 3 knife segments - 2 Coleman inserted outfeed rolls - 5 HP - No motors

ALLIED #40 Material Fan with 30 HP

• Manufacturer: Allied

-mounted on stand - 30 HP - still installed

Large Blower

- Shroud is 102" diameter x 28" wide - Fan is 61" diameter x 20" wide - Was run by a 150 HP motor (not included) - Needs paint job but mechanically sound - Located on West Coast of BC - Ready to load

Chicago Boiler Air Dryer

• Manufacturer: Chicago Boiler

- Two (2) air tanks - 31" diameter x 6'-4" long tank - 7.5 HP, 230/460 volt, 1750 RPM - Maximum psi - 150 @ 500 OF - Tank serial #807442-1 & 807442-2 - Built in 1980 - Some piping

20' Hemco Trimmer

• Manufacturer: Hemco

- Board dealer c/w 6 strand 81X, motor & drive - good condition - Trimmer - Left hand, 11 saws, 22" diameter carbide, 7 HP on "0" saw, 5 HP on all others, 11 cylinders, 9 air actuators. Will pass 24 ft board. Inf...

30' Rollcase (Approx.)

• Manufacturer: Canadian Mill Equipment

- Nine (9) 8" diameter x 26" face bedrolls c/w double single chain drive mounted onto a channel frame - No drive unit

8' x 40' Pel-Pro Single Pass Dryer

• Manufacturer: Pel-Pro

- 20 HP drive - ID of burner is 42" - ID of the heater is 54" x 18' long - PEL-PRO 8’ x 40’ Single-pass Drum-dryer c/w Drive unit. All is in good condition - The burner information: GP Combustion Equipment Inc.; ...

Hammer Hog System

- 21" x 36" opening - 250 HP, 1200 RPM, 460 volt motor c/w soft start - Screen has approx. 4" x 2" openings - Six (6) rows of hammers c/w spare set - 24" wide x approx. 16' long belt conveyor c/w MDI metal detect...