Building Filters
- Trusted Seller
10" Chip-N-Saw Mark II
used
- Manufacturer: Chip-N-Saw
- Build in 1978 - Forano knuckle style log turner - 18' half taper infeed c/w overhead hold down rolls and servo positioned lift - Mark II four sided canter - 2 x 4 spline bottom head - Drum style side heads c/w ...
Surrey, Canada - Trusted Seller
20" Chip-N-Saw Line
used
- Infeed chain conveyor - Log turner - Single length infeed for 20' c/w holddown rolls and servo positioner for bed lift - 4 sided canter (bottom head (2 x 4 spline), side heads and top head c/w servo positioners...
Surrey, Canada - Trusted Seller
44" NICHOLSON A2 RH AIR SEAL DEBARKER
used
- Manufacturer: Nicholson
- Built 1995 - Minimum log diameter is 4-1/2" - Five (5) Tool Air seal ring c/w remote tool tensioning - 100 HP, TEFC, 460 volt ring drive motor - Hydraulic ring centering - Fabricated main frame (appears in good...
Surrey, Canada - Trusted Seller
BM&M 6 X 12 CHIP SCREEN (4 ONLY)
used
- Manufacturer: BM&M
- Model: 6X12
BM&M 6 X 12 CHIP SCREEN (4 ONLY) - each screen has 2 decks but no bottom pan. Screens were originally installed at West Coast Cellufibre (Vancouver) at their whole log chipping facility. All fines dropped direct...
Surrey, Canada - Trusted Seller
COMACT DDM6 FOUR (4) SIDED CANTER SYSTEM
used
- Manufacturer: Comact
- Built in 1997 - 4" diameter to 12" diameter - 3", 4" and 6" cants - up to 450 FPM - DDM6 - Feedroll log turner - quad roll c/w positioning cylinders - One (1) pair of vertical and one (1) pair of horizontal inf...
Surrey, Canada - Trusted Seller
CAE Sharp Chain Reducer Quad Bandmill System
used
- Manufacturer: Sharp
- Knuckle style log turner - Centering infeed conveyor consisting of: - Four (4) pairs of idling centering rolls c/w mechanical centering linkages assembly - One (1) pair of hydraulically driven spiked feedrolls ...
Surrey, Canada - Trusted Seller
Comact DDM10 Line
used
- Manufacturer: Comact
- 10 years old - Approx. 120' V-flite conveyor including drive and attached control devices - Flying log turner - new HD upgrade 2011-12? (Quad roll) - DDM10 full profile machine, 480 volt - All drive units, moto...
Surrey, Canada 
VMAC Compressor-Generator-Welder Power System
new
- Manufacturer: VMAC
VMAC’s Compressor-Generator-Welder Power System offers performance in a single compact system. This system includes all the power you need on the jobsite to complete your work. The self-contained Compressor-Gener...
Nanaimo, Canada
VMAC 6-in-1 Power System – Kubota
new
- Manufacturer: Kubota
Nothing will stop you on the job site; with everything you need in a single compact Multifunction Power System, you will be ready for anything. The self-contained Multifunction system with a Kubota engine can be ...
Nanaimo, Canada
2011 North Pacific 38 Sedan 41.5'
used
- Manufacturer: North Pacific
2011 North Pacific 38 Sedan – "Raven Song" The North Pacific 38 Sedan is a proven coastal cruiser, admired for its solid construction, fuel efficiency, and timeless Europa-style design. Built in 2011, Raven Song ...
VMAC 5-in-1 Power System – Honda
new
- Manufacturer: Honda
Five power sources, one powerful machine.When you need the capabilities of multiple machines in a single powerful system, there is no better solution than the VMAC Multifunction Power System, powered by a Honda g...
Nanaimo, Canada- Trusted Seller
VKB 22" KODIAK LH DUAL RING DEBARKER
used
- Manufacturer: Kodiak
VKB 22" KODIAK LH DUAL RING DEBARKER - Built in 1997 - Model 622FS-2R LH - Left hand (ring pullout on right) - Two (2) six (6) tool air seal ring assemblies. (counter rotating) - Replaceable carbide tips - ...
Pacific Northwest, Cariboo, BC V0L 1H0, Canada - Trusted Seller
KETEK CY-100-CA
used
- Manufacturer: KETEK
Ketek CY-100-CA Brochure Features Dual chamber, controlled-air operation Secondary chamber gas residency time of two seconds Built in safety features Load-and-go operation Low power consumption Platform, ladder, ...
- Trusted Seller
KETEK CY-100-CA
used
- Manufacturer: KETEK
Ketek CY-100-CA Brochure Features Dual chamber, controlled-air operation Secondary chamber gas residency time of two seconds Built in safety features Load-and-go operation Low power consumption Platform, ladder, ...
- Trusted Seller
Comact DDM 12-SBP Profile Curve Sawing Canter Line
used
- Manufacturer: Comact
- Built in 2001 - 8' to 16' - 4" to 21" butt (maximum 23" envelope) - 400 FPM @ 60 hertz - 575 volt, 3 phase, 60 hertz - 'V' flight scanning conveyor approximately 58' long c/w 20 HP electric drive - Quad roll lo...
Surrey, Canada