Used browse categories

Norberg 15 ft. Rod Mill Head

• used

• Manufacturer: Norberg

Complete with Bearing Journal Diameter: 15 ft. | Length: 20 ft.

Allis Chalmers 6ft. x 12ft Rod Mill

• used

• Manufacturer: Allis-Chalmers
• Weight: 79,500 Lbs.

Tooth Count: Motor: Overall Dimensions Condition and Additional Notes: Automatic Rod Charger and Rods (6 Tons) are Available at Additional Cost

Norberg Rod Mill Shell and Feed Head

• used

• Manufacturer: Norberg

Complete with Bearing Journal Diameter: 15 ft. | Length: 20 ft.

Marcy 8 ft. 6 in. x 14 ft. Rod Mill

• used

Helical Main Gear 2 Pieces 262 Teeth x 17 in. Pinion Gear 18 Teeth x 17 in. Chute Feed/Overflow Discharge Air Clutch Bearings Rod Charger Using 500 HP Synchronous Motor @ 300 RPM (Not Available - Damaged) Bearing...

Marcy 5ft Dia. x 10ft Long Open-End Rod Mill

• used

• Manufacturer: Marcy

Equipped with Liners and Lifters Running Gear Mounted on Skid

Grinding Rods

• used

60 Tons 80% New 3.5 x 10 ft. - 20% 1 ¼ to 2 in. Balance all 3.5 Dia. x 10 ft. CR - 0.100 Mn - 0.783 Cu - 0.129 Zinc - 0.050 LEC 1.29

Cincinnati Machine No. 2 Cutter Grinder

• used

• Manufacturer: Cincinnati

For Sharpening Cutter Knives Overall Dimensions: Length: 48in | Width: 52.5in | Height: 55in

Allis Chalmers 9 x 12 Rod Mill

• used

• Manufacturer: Allis-Chalmers

9 ft. diameter. 12 ft. long. 1 piece shell. Cast steel feed and discharge heads. Main bearings with Babbitt inserts. 1 piece Herringbone ring gear. 302 teeth. 20 in. face. Gear guard. Sole plates. Westinghouse 40...

Dominion Rod Mill. 9.5 ft. x 14 ft. Long. 500 HP Motor.

• used

• Manufacturer: Dominion

Dominion Rod-Ball mill. 9.5 ft. Diameter x 14 ft. Long. 1 ¼” thick shell. Double helical bull and Pinion gear. 40” diameter x 24” wide self aligning babbit bearings. Farval manual bearing start-up lubricators. Fu...

1 in Ceramic Grinding Media

• used

Ceramic Grinding Media. 16 drums available. Approximately 700 lbs/drum. New/surplus grinding balls stored in sealed drums.

New Mill Components. New Grinding Mill Journal Bearing Lubrication & Lift Units. Please contact us with your requirements.

• used

14 ft. Rod Mill Charger Handler

• used

14 ft carriage. 3 hp drive motor. Chain drive to loading wheels 3 rubber wheels for rod loading. Manual hand crank positioning system. 6" dia. single flanges steel wheels track system 44" wide guage/spacing .

4ft x 10ft Hardinge Rod Mill

• used

• Manufacturer: Hardinge

4ft x 10ft Hardinge Rod Mill Single wave steel Liners. Peripheral end discharge. Herringbone bull and pinion gear. Gear guards General Electric Induction Motor. 50 hp 3 ph. 60 Hz 2200 volt 17.5 amps 435 rpm

3 inch Grinding Rods

• used

6 pcs. @ 3.5” dia. – 13.75 ft. long. 1 pcs. @ 3” dia. – 13.75 ft . long. 16 pcs. @ 2” dia. – 13.75 ft. long.

1/8 in. Grinding Media

• used

5 x Half Drums Approx. 1/8 in. (3mm) Grinding Media for Buhler Mills