Used Material Handling

BUNTING Drawer Magnet Used

• Manufacturer: Bunting

Inlet: 4 1/4 Outlet: 2 3/4 Flange: 7 3/4 x 7 3/4 Holes center-to-center: 6 3/4 x 6 3/4 Buyers are welcome to inspect equipment prior to purchase. Expedited shipping services are available upon request. This...

Generic Drawer Magnet Used

• Manufacturer: Generic

Inlet ID: 2 Outlet ID: 2 Flange: 4 1/2 x 4 1/2 Holes center-to-center: 2 1/2 x 2 1/2 Buyers are welcome to inspect equipment prior to purchase. Expedited shipping services are available upon request. This p...

BUNTING Drawer Magnet Used

• Manufacturer: Bunting

Inlet ID: 4 1/4 Outlet ID: 2 1/2 Flange: 6 x 6 Holes center-to-center: 4 3/4 x 4 3/4 Buyers are welcome to inspect equipment prior to purchase. Expedited shipping services are available upon request. This p...

BUNTING Drawer Magnet Used

• Manufacturer: Bunting

Inlet ID: 4 1/2 Outlet ID: 3 Flange: 6 x 6 Holes center-to-center: 4 1/2 x 4 1/2 Buyers are welcome to inspect equipment prior to purchase. Expedited shipping services are available upon request. This piece...

PPE TAL-15UFX Loader Used

• Manufacturer: PPE

1.1 kW 115 Volt Single Phase 60 Hz 3" Cylinder Height 6.75" Cone Height 7.75" Outside Diameter 6.5" Inside Diameter Tested Good Expedited shipping services are available upon request. All taxes due are ...

Generic Drawer Magnet USED

• Manufacturer: Generic

Inlet ID: 5 1/2 Outlet ID: 2 3/4 Flange: 7 x 7 Holes center-to-center: 6 x 6 Removed from: 750 Ton Engel Injection Molding Machine Model: ES 4400/750 Serial: 0454-750 Buyers are welcome to inspect equipme...

BUNTING Drawer Magnet Used

• Manufacturer: Bunting

TOP FLANGE: 7 1/2" X 7 1/2" TOP INLET HOLE DIAMETER: 4 1/4" BOTTOM FLANGE: 7 1/2" X 7 1/2" BOTTOM FLANGE INLET HOLE: 4 1/4" BOLT HOLES, CENTER TO CENTER: 6" Expedited shipping services are available upon req...

BUNTING Drawer Magnet Used

• Manufacturer: Bunting

TOP FLANGE: 7 1/2 X 7 1/2 TOP HOLE 4 1/4 BOTTOM FLANGE: 7 1/2 X 7 1/2 BOTTOM HOLE: 4 1/4 CENTER TO CENTER HOLE BOTTOM 6 INCH Expedited shipping services are available upon request. All taxes due are the res...

BUNTING 9063268-1-01 Drawer Magnet Used

• Manufacturer: Bunting

10" x 10" Top Flange 8" x 8" Holes Center to Center 4.25" x 4.25" Bottom Flange 3.25" x 3.25" Holes Center to Center 3" x 2" Top Opening 69 mm Outlet Inside Diameter Buyers are welcome to inspect equipment ...

BUNTING MAGNETICS Drawer Magnet USED

• Manufacturer: Bunting

7.5" x 7.5" Top Flange 4.25" Diameter Top Flange Inlet / Outlet Approx. 1.5" Cone Height 1.25" Cylinder 7.5" x 7.5" Bottom Flange 3 7/8" Diameter Bottom Inlet / Outlet Flange 6" x 6" Center to Center Holes ...

BUNTING Drawer Magnet Used

• Manufacturer: Bunting

Top flange:6 1/4x6 1/4 Top center to center:3 1/4x5 Inlet:2 3/4 Bottom flange:4 3/4x6 Bottom center to center:3 1/4x5 Outlet:2 3/4 Buyers are welcome to inspect equipment prior to purchase. Expedited shipp...

BUNTING MAGNETICS 62493-2 Drawer Magnet USED

• Manufacturer: Bunting

108.62 mm Diameter Inlet / Outlet Top Flange 6" x 6.5" Top Flange 5" x 5" Center to Center Holes Top Flange 7.75" x 7.75" Bottom Flange 6.75" x 6.75" Center to Center Holes Bottom Flange 1.5" Cone Height 1....

40' high cube 8’ wide x 9’6” tall swing doors on one end wood deck rings for tie downs inside

40' high cube 8’ wide x 9’6” tall, swing doors on one end, wood deck, rings for tie downs inside, scattered dings/dents, decking showing wear in a couple spots, weighs approx. 8,470 lbs, used

40' high cube 8’ wide x 8’6” tall swing doors on one end wood deck rings for tie downs inside

40' high cube 8’ wide x 8’6” tall, swing doors on one end, wood deck, rings for tie downs inside, scattered dings/dents, decking showing wear in a couple spots, weighs approx. 8,160 lbs, used

Meto Corp Material Handling M2210

• Manufacturer: Meto Corp

Metolift, Model M2210-00, column barrel dumper. Rated to a maximum capacity of 220 lbs. Equipped with a 24" diameter x 32" high chamber and has a discharge height of 146".