2007 ATLAS COPCO ECM720
used
- Manufacturer: Atlas-Copco
- Model: ECM 720
4.5” – 5.5” Inch Class CAT C11 Diesel Engine HC200A Drifter set up for GT60 Rods Caterpillar C11 Diesel Engine Montabert HC200A drifter. Recent new hydraulic Pump Aprox. 11800 total frame hours Unit is set up for...
Louisville, KY
2005 INGERSOLL-RAND ECM660 III
used
- Manufacturer: Ingersoll Rand
- Model: ECM-660 III
3.5 – 4.5 Inch Class HC160R Drifter w/ Only 82 Percussion Hours since Rebuild Cummins Diesel Engine 7572 Engine Hours 2517 Percussion Hours Extendable Boom Digital Angle Indicator Auto Rod Changer Dust Collector ...
Louisville, KY
2003 SANDVIK D55SP
used
- Manufacturer: Sandvik
DTH Class 3508 Cat Engine Single Pass Unit Currently using a 8” DTH Hammer with a 9” Bit Equipped w/ ( 2 ) 6 ½” x 25 ft. Drill Pipe w/ 8” DTH Hammer Dust Collector Mast 73’ Long, U/C 85% – Excellent condition. Un...
Louisville, KY
2005 Sandvik Pantera 1500
used
- Manufacturer: Sandvik
21,163 frame hours 11,015 percussion hoursSet up for T51 Well maintained for age
2024 SOOSAN JD800E-II
used
- Manufacturer: Soosan
New 2024 Soosan JD800E-II Rock Commander w/ QSB6.7 Series Tier 4 Final Equipped with JET9II Drifter 235 CFM @ 150 PSI Air Package Can be setup for T38, T45, or T51 – Customer Choice Unit starts a 14’ft starter st...
Louisville, KY
2019 Furukawa HCR1450EDII Stock# 4501
used
- Manufacturer: Furukawa
- Model: HCR1450EDII
Unit has 4,235 total hours Unit will be fully cleaned and freshly serviced. Excellent condition.
2006 Atlas Copco ROC D3
used
- Manufacturer: Atlas-Copco
- Model: ROC D3
Equipped with COP 1240 Drifter 28 hours on machine since upgrades: New track chains New Ecm motor control New mast roller New cable New nose cone seals New accumulator diaphragms 2 new control switches at control...
1997 Ingersoll Rand ECM590
used
- Manufacturer: Ingersoll Rand
- Model: ECM-590
– Equipped with YH80A Drifter – Ready to work – Repairs needed are one door with broken hinges – Fuel stop solenoid – This machine has a new air end and has less than 200 hours on hydraulic pump
2005 Ingersoll Rand ECM590
used
- Manufacturer: Ingersoll Rand
- Model: ECM-590
– Equipped with YH80A – Ready to work – Repairs needed are inoperable fuel stop solenoid
2006 Ingersoll Rand ECM590
used
- Manufacturer: Ingersoll Rand
- Model: ECM-590
– Equipped with YH80A Drifter – Repairs needed or in the process of being repaired – Dust collector top new part has been fabricated need’s installed – Rod changer arm is broken have new parts to replace purchase...
2004 Ingersoll Rand ECM590
used
- Manufacturer: Ingersoll Rand
- Model: ECM-590
– Equipped with YH80A Drifter – Mechanic believes there is a broken pin in the fuel injection pump machine will idle but will not idle up. – Other repairs needed are inoperable fuel stop solenoid
2004 Ingersoll Rand ECM590
used
- Manufacturer: Ingersoll Rand
- Model: ECM-590
– Comes with YH70 not currently installed but will be mounted for transport – This unit has tracking issues will move but unknown if it’s the final drives or hydraulic motors. – Hammer needs to be mounted back on...
2000 Ingersoll Rand ECM590
used
- Manufacturer: Ingersoll Rand
- Model: ECM-590
– Equipped with YH80A Drifter – Unit needs nothing is currently running on a job at this time. – Has newer paint job – Manual rod changer – Long boom
Furukawa HD712 Hydraulic Drifter
new
- Manufacturer: Furukawa
HD712 Hydraulic Drifter / Hammer – Surplus / New For use on the following Furukawa machines: HCR1200ED HCR1200EDII
2005 INGERSOLL-RAND ECM660 III
used
- Manufacturer: Ingersoll Rand
- Model: ECM-660 III
Montabert HC160 Drifter Setup for T45 Cummins Diesel Engine Unit shows 2,307 engine hours, we estimate approximately 12,307 total frame hours 3,949 Percussion hours
Ingersoll Rand CM-682 Drilling Rig
used
- Manufacturer: Ingersoll Rand
- Model: CM-682
Good condition Ingersoll Rand CM-682 Drilling Rigs manufactured in 2001. Located in USA and other countries. Click request price for more information.
USA
Tip: Enter manufacturer, model or keyword