Processing » Extruders

Search By Manufacturer

Search By Country

Building Filters

1759

Used unit

  • Trusted Seller
    1962 WEAN UNITED 1675 ton

    1962 WEAN UNITED 1675 ton Aluminum Extrusion Line

    • Manufacturer: Wean

    Manufacture: - Youngstown 1962 - Rebuilt by Wean-United 1988 - Decommissioned 2022 Tonnage: - 1675 US tons Billet Size - 7" diam (178mm) Equipment - Billet load station - Billet Heater - BELCO natural gas fire...

    Banner Elk, NC
  • Winkworth ZX500-6 Z-Blade Mixer-Extruder |

    Winkworth ZX500-6 Z-Blade Mixer-Extruder | 500L Working | Vacuum Lid | Jacketed | 304 SS | With Tool Temp Units

    • Manufacturer: WinkworthWinkworth

    10151559 Used Winkworth ZX500-6 Z-Blade Mixer/Extruder | 500L Working | Vacuum Lid | Jacketed | 304 SS | With Tool Temp Units. 500 liter (132Gal) working capacity with a 778 liter total capacity (product dependen...

    Belvidere, IL
  • Flender 6" Plastic Extruder

    Flender 6" Plastic Extruder

    • Manufacturer: Flender

    One (1) Used Flender 6" (150mm) Plastic Extruder, 30:1 L/D, no motor, direct drive, lowboy gearbox, unitized base, rated at 500 HP (372 KW)

    Cleveland, OH
  • NRM 8" Hot Feed Rubber

    NRM 8" Hot Feed Rubber Extruder

    • Manufacturer: NRM

    One (1) Used 8" NRM Hot Feed Extruder, right hand feed, pneumatically adjustable sheet head, GB ratio 20.5:1, unitized base, date 12-74, Order 104353, S/N T-18580

    Cleveland, OH
  • Farrel 4.5" Plastic Extruder

    Farrel 4.5" Plastic Extruder

    • Manufacturer: Farrel

    Item 6556 - One (1) Used Farrel 4.5" (120mm) Plastic Extruder, 12:1 L/D, 125 HP 1750/2000 RPM 500 VDC motor, direct drive, lowboy gearbox, unitized base, no head

    Cleveland, OH
  • Barwell C3 Preformer

    Barwell C3 Preformer

    • Manufacturer: Barwell

    One (1) Used Barwell C3 Preformer, Barwell_Rubber_Preformer, capacity 120 lbs, 10" x 55" chamber, Motor 460V, 60 Cycle, Max PSI 2500.

    Cleveland, OH
  • Siemens Extruder Drive

    Siemens Extruder Drive

    • Manufacturer: Siemens

    One (1) Used Siemens 75 HP Microprocessor DC drive, S/N 16-96-D3607501-01.

    Cleveland, OH
  • UFS 1.5" Cold Feed Rubber

    UFS 1.5" Cold Feed Rubber Extruder

    • Manufacturer: UFS

    Item 6006-1 - One (1) UFS United Feed Screws 1.5" 38mm Cold Feed Rubber Extruder, 20:1 L/D, 14.5:1 G/B ratio, Siemens 20 HP 1755 RPM 460 VAC motor, AC VFD variable frequency drive, control panel, clamp assembly, ...

    Cleveland, OH
  • UFS 1.5" Cold Feed Rubber

    UFS 1.5" Cold Feed Rubber Extruder

    • Manufacturer: UFS

    Item 6006-2 - One (1) UFS United Feed Screws 1.5" 38mm Cold Feed Rubber Extruder, 20:1 L/D, 14.5:1 G/B ratio, Siemens 20 HP 1755 RPM 460 VAC motor, AC VFD variable frequency drive, control panel, clamp assembly, ...

    Cleveland, OH
  • Farrel 15" 250mm Hot Feed

    Farrel 15" 250mm Hot Feed Rubber Extruder

    • Manufacturer: Farrel

    Item 6205 - One (1) Used Farrel 15” Dump Extruder, drop extruder, hot feed extruder, feed opening 36” wide x 24.5” deep, stuffer 35” wide x 8” thick with 13” stroke, 95:1 total gearbox reduction (19.4:1 primary g...

    Cleveland, OH
  • Werner & Pfleiderer Twin Screw

    Werner & Pfleiderer Twin Screw Extruder

    • Manufacturer: WP

    One (1) Used Werner & Pfleiderer 58mm Twin Screw Extruder, twin screw compounder, continuous mixer, 16:1 L/D, Type Continua 58, Reliance Motor 25HP DC 1750RPM 500V, Gearbox rated for 40HP, co-rotating, 3 heating ...

    Cleveland, OH
  • NEW Nakata Triplex Sidewall 200P

    NEW Nakata Triplex Sidewall 200P x 200P x 200P Extruder

    • Manufacturer: NEW Nakata

    One (1) NEW Nakata 'TRIPLEX 200P×200P×200P' Triple Sidewall Rubber Extruder, Piggyback Configuration, Cotter Clamp Type, Model TRIPLEX 200P×200P×200P, S/N E235067~5077, YOM 2025, Description of Asset: φ200mm Pin ...

    Cleveland, OH
  • Farrel 10" Hot Feed Rubber

    Farrel 10" Hot Feed Rubber Extruder

    • Manufacturer: Farrel

    One (1) Used 10" Farrel Hot Feed Rubber Extruder, roller feed, Motor 200 HP, 500 volt, 1750 rpm.

    Cleveland, OH
  • RMS Single Roll Roller Die

    RMS Single Roll Roller Die

    • Manufacturer: RMS

    One (1) used RMS roller die head, 6” ID inlet mating with extruder, 23” roll face, approximately 20” usable surface, 12” diameter roll, used to produce tire tyre tread

    Cleveland, OH
  • Farrel 15" Rubber Dump Extruder

    Farrel 15" Rubber Dump Extruder

    • Manufacturer: Farrel

    Item 6328 - One (1) Used Farrel 15” Rubber Dump Extruder, drop extruder, hot feed extruder, feed opening 36” wide x 24.5” deep, stuffer ram 35” wide x 8” thick with 13” stroke, 95:1 total gearbox reduction (19.4:...

    Cleveland, OH
12345

Overview

Extruders are machines used in the manufacturing process to shape materials by forcing them through a die. Commonly used in plastic and metal industries, extruders are essential for creating products like pipes, sheets, and profiles. Their versatility allows them to handle various materials, including polymers, rubber, and even food products.

FAQ

What should I consider when buying a used extruder?

Evaluate the extruder's condition, age, and previous usage. Check for signs of wear, especially on the screw and barrel, and ensure the machine has been well-maintained.

How do I ensure the extruder is shipped safely to my location?

Hire a logistics company experienced in transporting heavy machinery. Make sure the extruder is properly secured, and all parts are protected from damage during transit.

What is the maintenance schedule for an extruder?

Regular maintenance includes inspecting the screw and barrel for wear, checking and replacing filters, and ensuring the cooling and heating systems are functioning properly. Follow the manufacturer’s guidelines for specific maintenance intervals.