Used tester in Taiwan

H.D.T. Heat Deflection Tester Confirm to ASTM D648 ISO 75-1 Standard

• Manufacturer: cometech testing machines

The specimen is given a stress at the center, and the temperature should increase by 2 degrees Celsius per minute. When the specimen’s center area reach the deflection of 0.254mm, the temperature is determined as...

DIN Abrasion Tester Confirm to DIN53516 ISO-4649 GB/T 9867 SATRA TM174 Standard

QC-618A is suitable for elastic material, rubber, tires, conveyor belts, transmission belts, shoe soles and software synthetic leather. The specimen of wear area is dia. 16mm which provide the required load and t...

Digital Metal Impact Tester Confirm to EN 10045, ASTM E 23-00a, GB T229 Standard

• Manufacturer: cometech testing machines

QC-9130(A) is suitable for metal material of large capacity impact tester. It used hammer once of swing impact specimen which broken was based on hammer of initial angle and after strike of angle to get hammer of...

Compression & Deformation Tester Confirm to ASTM-D395, JIS K6262, GB/T 7759, ISO 815 Standard

• Manufacturer: cometech testing machines

It is use static state way to testing rubber under constant compression and exerting heat condition to check the permanently deformation rate of the material. This test needs to collocate with oven and Thickness ...

QC-652B/C/D/E Melt Flow Index Tester Confirm to ASTMD1238, D3364, ISO1133, GB- T3682 Standard

• Manufacturer: Cometech Testing Machines

Melt Flow Index Tester can test thermoplastic melt mass flow rate (MFR) and melt volume flow rate (MVR), also known as MI or MFI. The Flow Indexer QC-652B can perform ISO/ ASTM standards test methods, equip with ...

Drop Weight Impact Tester Confirm to BS EN 1621-1-2012、 BS EN 1621-2-2014 Standard

• Manufacturer: cometech testing machines

This tester is applied on buffer material test with a standard weight of 5kg hammer, drop height is usually 100cm, can produce about 50 joules to hit against test pieces vertically. This tester can read remaining...

QC-639V/W Impact Tester Digital Type Confirm to ASTM D256、ASTM D6110、ISO179、ISO180、ISO13802 Standard

• Manufacturer: cometech testing machines

Impact Tester Digital Type can measure the impact resistance of polymer materials. It calculates the absorbed impact energy based on the energy conversion relation. The precision of the impact hammer will highly ...

MIT Folding Endurance Tester Confirm to TAPPI T423PM 、 ASTM D2176 、 JIS P8115 、 GB/T 2679.5 、 ISO 5626 Standard

• Manufacturer: Cometech Testing Machines

MIT Folding Endurance Tester is for testing the material's folding endurance strength, the machine can test the available bending times when the material bear the tension and bending angle (from +135 degree to -1...

Tape Holding Power Tester (Normal Type) 10 sets Confirm to GB/T 4851, ASTM D3654, PSTC 7 Standard

• Manufacturer: cometech testing machines

QC-801(A)(B)(C) Specimen stick test area can use 1/2”x1”or 1”x1”, unified to use 0.45 pound of load scrunch through specimen, hanging counterweight in the lower end of specimen. Timer automatically stops counting...

Portable Pencil Hardness Tester Confirm to ASTM D3363, ECCA T4, MILC27 227, NEW5350, SIS184187, SNV37113, JIS-C3003/D0202 Standard

GI-M010 according to WolffWilborn standard, this tester is designed to measure the coating surface hardness scrape-resistance, applied to experiment analysis or control production quality, suitable products inclu...

Electric Pencil Hardness Tester Confirm to ASTM D3363, ECCA T4, MILC27 227, NEW5350, SIS184187, SNV37113, JIS-C3003/D0202 Standard

GI-M023 according to WolffWilborn standard, this tester is designed to measure the coating surface hardness scrape-resistance, applied to experiment analysis or control production quality, suitable products inclu...

Spray Tester Confirm to JIS- L1092 , BS EN 24920 , AATCC-22 , ISO 4920, ASTM D1913-2000, ASTM D583-54 Standard

• Manufacturer: cometech testing machines

QC-305 may test water-proof or non-water-proof textile surface water resistance. Clamping textile with 45 degree angle on grip, hold open around 150mm diameter plane, putting sprayer above sample center 150mm, sp...

QC-116 Digital Bursting Strength Tester Confirm to ISO-2759, GB/T 6545, JIS-P8112, JIS-L1018, ASTM-D2210, TAPPI-T403 Standard

Digital Bursting Strength Tester is used for testing the bursting resistance for samples such as base paper, corrugating paper, leather, synthetic leather. This tester is a digital type that features automatic co...

LCD Monitor Carton Packaging Compression Tester Confirm to ISO 12048 ISO 2872 ASTM D4169 TAPPI T804 GB T4857-4 JIS Z212 Standard

• Manufacturer: cometech testing machines

This model is designed for test large LCD screen packaging materials such as Styrofoam or other materials package container to proceed with whole carton compression strength test.Load measuring adopt three point ...

QC-113A Pneumatic Type Drop Tester Confirm to ASTM 5276 / GB/T 4857.5 / CNS 2999 / ISTA 1A / ISTA 2A Standard

• Manufacturer: cometech testing machines

Suitable for testing the impact resistance of packaging and electronic products during transportation. It features a single-wing structure, occupies a small space, and is typically used to simulate product impact...