Building Filters
MUDCAT MC2000 AUGER DREDGE #3608
MUDCAT MC2000 AUGER DREDGE (Ref#3608 ) 2 available, (1) Built 2001 and (1) built 1999 with Cummins Tier 4i engines, 24" diameter auger, 20,000 lb torque, 20' depth, forward/reverse digging, currently on land, loc...
IMS VERSI-DREDGE MODEL 4010 #4236
IMS VERSI-DREDGE MODEL 4010 (Ref#4236 ) Built 1993, 4311 hours, 5.9L Cummins 177 hp 6 cylinder engine, 20' digging depth, 8' auger head, cable travel with windlass drive, haul trailer with pintle hitch, fittings,...
8" CUTTERHEAD BELL DREDGE PUMP #4267a
8" CUTTERHEAD BELL DREDGE PUMP (Ref#4267a) Used on one job, very good condition. (it was attached to a Cat 336 long reach excavator to dredge 50'). Price : $90,000
16" x 18" CUTTERHEAD DREDGE #3449
16" x 18" CUTTERHEAD DREDGE (Ref#3449) Built 2012. 102' x 23'6", hull depth 5'. Ladder length: 55'. Minimum depth: 6', max depth 44'. Center section: 36' x 11' x 5'. Side pontoons: 90' x 6' x 5'. Dredge pump: Pea...
$1,775,000 USDOceanside, NY
8" SDR17 HDPE DREDGE PIPE #4179a
8" SDR17 HDPE DREDGE PIPE (Ref#4179a) 3,900' available, 40-50' sections, located Florida Price : $8 per foot 10" SDR17 HDPE DREDGE PIPE (Ref#4179b ) 750' available, 40-50' sections, located Florida Price: $12 per...
Oceanside, NY
MUD CAT 115D DREDGE #3731
- Manufacturer: Caterpillar
MUD CAT 115D DREDGE (Ref#3731) Built 2020, used very little (less than one week), 15' working depth, 8' cut width, 17" cut height, 22.5" avg draft, Catamaran hull type, John Deere 125 hp engine, 60 gal fuel capac...
ELLICOTT 890 CUTTER HEAD DREDGE #3764z
- Manufacturer: Ellicott
ELLICOTT 890 CUTTER HEAD DREDGE (Ref#3764z) Built 1981, 11" x 14", 1000 hp, 79' hull length, 18" draft, 6'-28' dredge depth, 130-146' radius, complete, located Mid West Price Open
Oceanside, NYMUDCAT SP915 8" AUGER DREDGE #4191
MUDCAT SP915 8" AUGER DREDGE (Ref#4191) 15' depth. 32' length. Detroit 6 cylinder. 8" discharge. Cutter head width: 98". Capacity: 2000 gallons per minute. Thomas pump. Replaced main gear box – rebuilt box $30k, ...
Oceanside, NY
12" x 12" ALL ALUMINUM CUTTERHEAD DREDGE #3400
12" x 12" ALL ALUMINUM CUTTERHEAD DREDGE (Ref#3400) Built 2019, Overall length (with ladder) 46'. Hull length 30' plus 7' ladder. Overall width: 11.4'. Hull depth: 3.5'. Average draft (with fuel): 2' Aluminum uni...
$575,000 USDOceanside, NYSDR 17 10" DREDGE PIPE #4126b
SDR 17 10" DREDGE PIPE (Ref#4126b) Approx 12000' in 46-48' lengths Price : $12 per foot
Oceanside, NY
14" x 12" AAMCO CUTTERHEAD DREDGE #2787a
- Manufacturer: Ammco
14" x 12" AAMCO CUTTERHEAD DREDGE (Ref#2787a) Reworked 2013 / Repowered 1995, Hull rebuilt / refurbished 2014, 65' x 24' x 5', draft 3', 7000 gal fuel capacity. 700 HP CAT 3412 Pump engine, GIW dredge pump, 14" S...
- Trusted Seller
Dredge Velocity Control System DWV-5
This is the main part of our production system. Adding water to maintain velocity ” flow” -decreases production. In dredging, when the density changes the pump rpm also needs to change. If rpm is not adjusted yo...
10 x 12 ELLICOTT 370 CUTTERHEAD DREDGE #3166
- Manufacturer: Ellicott
10 x 12 ELLICOTT 370 CUTTERHEAD DREDGE (Ref#3166) Built 1980s. 250 cubic yard per hour capacity. 20' depth capacity. Main engine: CAT 3406 diesel. Dimensions: 36' x 12' x 4', with 2'8" draft. Weight: 56,000lb. Fu...
8" X 8" DSC MORAY DREDGE #4185c
8" X 8" DSC MORAY DREDGE (Ref#4185c ) 42.8'L x 18.5'W, 17.5' depth, 42,000 lb overall weight, 19.5" impeller dredge pump, 25 hp cutter power, cylinder ladder lift/swing, 8" square spud, articulating rear spud, Ca...
16" x 16" ELLICOTT SERIES 1270 DRAGON DREDGE #3877
- Manufacturer: Ellicott
16" x 16" ELLICOTT SERIES 1270 DRAGON DREDGE (Ref#3877 ) 50' max dredging depth, 125' swing width at minimum dreding depth, 92' swing width at maximum dredging depth, Cat 3508 engine (1000 hp) Marine Tier 3 (heat...
$1,600,000 USDOceanside, NY
Rohr KS220 Dredge
- Manufacturer: Rohr
- Model: KS220
Good condition Rohr KS220 Dredges manufactured in 1994. Located in Germany and other countries. Click request price for more information.
Germany
