Used Processing in Oregon, USA

Jacobson Hammer Mill, Model P-361D Pulverator Center Feed Hammer Mill

• Manufacturer: Jacobsen

Used Jacobson Model P-361D Pulverator Center Feed Hammer Mill, S/N 29504. 125HP 230/460V 1775 RPM motor direct drive rotor. 17” x 24” top infeed opening with 6” auger in bottom of hopper to meter wood into hamm...

Schutte Hammermill, Model 1360 Hammermill

• Manufacturer: Schutte

Used Schutte Model 1360 Hammermill. Top infeed is 21-1/2" x 23". Currently has 1" thick swinging hammers. Screen included (not installed) has 1/2" dia. round holes. Has been modified to a pneumatic discharge. ...

Lightnin 1.74 Hp Mixer With Tank Clamp

• Manufacturer: Lightnin

Lightnin 1.74 Hp Mixer With Tank Clamp And 11" Dia. 3 Blade Propeller. Final RPM is 350. Motor is TEFC and requires 220/440 volt, 3 phase. Will be test run. See photos of Lightnin 1.74 Hp Mixer With Tank Clamp...

Pangborn Baghouse-Filter

• Manufacturer: Pangborn

Pangborn Baghouse-Filter. Has forty nine 4" dia. by 80" long bags for approximately 340 sq. ft. of cloth. Dirty air inlet is a 12" dia Unit was originally mounted against a wall so it is equipped with a back su...

Carter Day Baghouse, Model 144RJ60 Baghouse

Carter Day Model 144RJ60 Baghouse. Has been disassembled for shipment. 1,920 sq. ft. of cloth area. Includes support structure, maintenance platforms and ladders. Also equipped with small high pressure system ...

Belt Conveyor Head Drum 36" dia. X 51" wide

Conveyor Head Drum 36" dia. X 51" wide, rubber slide lagging, 3-7/16" shaft and bushings. See photos of Belt Conveyor Head Drum 36" dia. X 51" wide on our web site. Inventory No. CHD-2. Located at our Portland...

Dodge Belt Conveyor Tail Drum, 30" dia. X 44" wide

• Manufacturer: Dodge

Dodge Belt Conveyor Tail Drum, 30" dia. X 44" wide, # K35YZ, new-surplus. Requires #3535 taper-lok bushings. See photos of Dodge Belt Conveyor Tail Drum on our web site. Inventory No. CTD-4 Located at our Portl...

Roach Conveyor, Plastic Belt Curve Conveyor 14" X 12

Roach Plastic Belt Curve Conveyor, 14" wide by nominal 12'6" long, with adjustable legs, 1/2 HP, 230/460 volt TEFC gearmotor, rollerchain drive and guard. Condition appears to be very good. Will be test run pri...

Sutorbilt Blower 8 X 20 Model 8L

Sutorbilt Blower, Model 8L, size 8x20, 1.7 displacement, Serial No. A5440. See photo of used Sutorbilt Blower on our web site. Inventory No. 9260. Located at our Portland, Oregon facility.

Sutorbilt Blower 12 X 20 400 series

12 x 20, 400 Series Sutorbilt Blower S/N A5520. Includes base, inlet and outlet elbows and both sheaves. See photo of used 12 x 20, 400 Series Sutorbilt Blower on our web site. Inventory No. 9560. Located at o...

Shavings Transport System

Shavings Transport System. Originally used to transport shavings to the top of a chip bin by vacuum. Consists of Cincinnati model HP-8D21 high pressure vacuum blower with 20 hp TEFC motor, v-belt drive with gua...

Carter Day Baghouse, Carter Day 144RJ60 Baghouse

Carter Day 144RJ60 Baghouse. Has been disassembled for shipment. 1,920 sq. ft. of cloth area. Includes support structure, maintenance platforms and ladders. Also equipped with small high pressure system to tra...

Pangborn Baghouse-Filter

• Manufacturer: Pangborn

Pangborn Baghouse-Filter. Has forty nine 4" dia. by 80" long bags for approximately 340 sq. ft. of cloth. Dirty air inlet is a 12" dia. Unit was originally mounted against a wall so it is equipped with a back ...

Material Blower Remanufactured by Western Pneumatics

Material Blower Remanufactured by Western Pneumatics. Size 35 with 9" wide X 22-1/2" dia. 6 blade wheel with full back ring and open front. 12" dia. inlet and extended 11-3/4" X 12-3/4" flanged discharge. V-b...

Pneumatech Air Dryer, Heatless Regenerative Air Dryer

Pneumatech Heatless Regenerative Air Dryer, Model PH-100, S#0010-S134592-020975, capacity is 100 SCFM, purge pressure 47 PSIG, Max. pressure 150 PSIG, voltage 115 volt- 1 phase- 60 cycles, requires dessicant AA1/...