Used Foundry & Casting

Vintage Falcon Cast Iron and Oak Slat Bench - 1950's?
- Manufacturer: Oak
“Great condition” Vintage Falcon Cast Iron and Oak Slat Bench - 1950's? We don't know a whole lot about this, but judging by what we could find on the internet, it may have been manufactured in the 1950's. If tha...
$1,500 USD
Springfield, IL
Trusted Seller
T-Slotted Floor Plates (1) 86" x 157" Floor Plate, Brand New Cast Iron
- Manufacturer: NEW
Features: Brand New Plate, Delivery Approx. 5-Months From Order Cross Slots Equipped With: Leveling Screws MATERIAL: SURFACE TREATMENT: Side Skirt Painted & Anti-Rust Primer Paint on Bottom NOTES: Brand New Plate...
Melville, NY
Trusted Seller
TLV J7.5B-10 Cast Iron Steam Trap. Size 3
- Manufacturer: TLV
TLV J7.5B-10 Cast Iron Steam Trap Comes as shown in photos. New condition. Please contact us if you have any questions Shipping is the responsibility of the buyer, but we can help you get a shipping quote. You c...
$1,600 USD
Aiken, SC
Trusted Seller
Auction
{each} MUELLER CAST IRON 18" WATER METER FLAT LID
- Manufacturer: Mueller
Quantity: 7 MUELLER CAST IRON 18" WATER METER FLAT LID Auctioneer's Note: Please remember you are bidding per piece. Your bid is multiplied by the quantity to establish the total lot price.
Riverdale, NJ
Visit Auction Website
Trusted Seller
Auction
{each} MUELLER CAST IRON 18" WATER METER FLAT LID
- Manufacturer: Mueller
Quantity: 7 MUELLER CAST IRON 18" WATER METER FLAT LID Auctioneer's Note: Please remember you are bidding per piece. Your bid is multiplied by the quantity to establish the total lot price.
Riverdale, NJ
Visit Auction Website
Trusted Seller
BHD Tetrehedron 2"
- Manufacturer: Giant Finishing
BHD- Black High Density Media will minimize time cycles on softer metals without the impingement of hard ceramic medias. Media has fine aluminum oxide for fine finishes, smooth RA’s in minimal time cycle.
Addison, IL
Goulds Cast Iron Industrial 3175 Centrifugal Paper Stock Pump 4-6x18 Size
- Manufacturer: Mersen/Ferraz/Gould-Shawmut
Goulds Industrial Cast Iron Centrifugal Pump Model #: 3175 Size: 4-6x18
$2,750 USD
Cedarburg, WI
3' x 57'' T-Slot Cast Iron Riser Block w/Drilled and Tapped Holes
Cast Iron Riser Blocks Drilled and Tapped Holes T-Slot Surface Dimensions: 36" x 57" 8" Riser Block Height
$1,800 USD
Cedarburg, WI
Trusted Seller
Air Max Air compressor 7.5 hp 1 ph. two stage, Cast iron, 80 gallon, quiet air
- Manufacturer: Air-Max
We are A full service air center, specialize in rebuilding complete units and air ends. We have fully stocked service trucks since 1982 The picture is A stock photo As I have over 100 units here. Photo is just t...
$3,790 USD
Waupaca, WI
Trusted Seller
Air Max Air compressor 5 hp 3 ph. two stage, Cast iron, 80 gallon, quiet air
- Manufacturer: Air-Max
We are A full service air center, specialize in rebuilding complete units and air ends. We have fully stocked service trucks since 1982 The picture is a stock photo of a new air compressor. Please read the descr...
$2,990 USD
Waupaca, WI
6' x 42" Heavy Duty 2" Thick Top Cast Iron Setup Fixture Table
Heavy-Duty Cast Iron Precision Setup Fixture Table Drilled & Tapped Holes Table Top Thickness: 2 1/4" Dimensions: 6' x 42" Working Height: 21 3/4"
$5,500 USD
Get financing
Est. $108/mo
Cedarburg, WI
Trusted Seller
Air Max Air compressor 5 hp 1 ph. two stage, Cast iron, 80 gallon, quiet air
- Manufacturer: Air-Max
We are A full service air center, specialize in rebuilding complete units and air ends. We have fully stocked service trucks since 1982 The picture is a stock photo of a new air compressor. Please read the descr...
$3,290 USD
Waupaca, WI
Trusted Seller
Air Max Air compressor 7.5 hp 3 ph. two stage, Cast iron, 80 gallon, quiet air
- Manufacturer: Air-Max
We are A full service air center, specialize in rebuilding complete units and air ends. We have fully stocked service trucks since 1982 The picture is a stock photo of a new air compressor. Please read the descr...
$4,990 USD
Waupaca, WI
29.5" x 17.5" Cast Iron Inspection/Layout/Setup Table 1 1/4'' Surface Thickness
- Manufacturer: Unbranded/Generic
30" x 18" Cast Iron Inspection/Layout/Setup Table Surface Dimensions: 29.5" x 17.5" Surface Thickness: 5/8" Webbed Base Design for Added Stability
$500 USD
Cedarburg, WI
Accurate Gage Inc. 30" x 17.5" Cast Iron Inspection/Layout Table 1-1/4" Surface
- Manufacturer: Accurate Gage Inc.
Accurate Gage Inc. 30" x 17.5" Cast Iron Inspection/Layout Table Surface Dimensions: 17.5" x 29.5" Surface Thickness: 1 1/4"
$300 USD
Cedarburg, WI