- Trusted Seller
DAVIS STANDARD 150INDS-20
- Manufacturer: Davis-Standard
Used 1.5” Davis Standard Vented Single-Screw Extruder Model: 150IN DS-20 Driven by a nontagged motor and a Reliance model GV3000 AC drive Gearbox: 6.53:1 ratio, rated for 50 hp, 1.25 service factor, 152 rpm screw...
Hainesport, NJ - Trusted Seller
DAVIS STANDARD 4.5"
- Manufacturer: Davis-Standard
Used 4.5" Davis Standard 30/1 L/D Extruder, Electrically Heated Air Cooled Barrel. Includes gearbox with 17.36/1 gear ratio rated at 321 hp. Serial #M3316, SO #05432. New 10/1991. Includes Kryenborg Type K-SWE-12...
Hainesport, NJ - Trusted Seller
1991 DAVIS STANDARD 4.5"
- Manufacturer: Davis-Standard
Used 4.5" Davis Standard 30/1 L/D Extruder, Electrically Heated Air Cooled Barrel. Includes gearbox with 17.36/1 gear ratio rated at 321 hp. Serial #M-3315, SO #05432. New 10/1991. Includes Kryenborg Type K-SWE-1...
Hainesport, NJ - Trusted Seller
2000 DAVIS STANDARD 5.11"
- Manufacturer: Davis-Standard
Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...
Hainesport, NJ - Trusted Seller
1997 DAVIS STANDARD 5.11"
- Manufacturer: Davis-Standard
Used 130mm (5.11") 30/1 L/D Non-Vented Davis Standard Extruder. Driven by 250 hp DC motor with 42" centerline air cooled barrel. Includes heat panel (without temperature controller), SCR controller and 6" continu...
Hainesport, NJ - Trusted Seller
2001 DAVIS STANDARD PEDESTAL
- Manufacturer: Davis-Standard
- Model: PEDESTAL
Used 1.25" Davis Standard Pedestal Extruder With 36/1 L/D Vented Barrel. New 2001. Has electrically heated air cooled barrel, includes temperature control panel and 5 hp AC motor, 230/460 volt. Previously used as...
Hainesport, NJ - Trusted Seller
DAVIS STANDARD 1.5"
- Manufacturer: Davis-Standard
- Model: 15
Used 1.5" Davis Standard 28/1 L/D Non-Vented Air Cooled Extruder. New in 1989. Equipped with 6.53/1 gearbox ratio. Gearbox is belt driven through a 15 hp DC motor. Includes temperature control panel with motor dr...
Hainesport, NJ - Trusted Seller
DAVIS STANDARD 48"
- Manufacturer: Davis-Standard
Used Davis Standard sheet take-off unit consisting of (3) 48" face rolls mounted in a vertical arrangement for a downstack operation. All three rolls measure 16" in diameter. Top roll is tungsten and the middle a...
Hainesport, NJ - Trusted Seller
DAVIS STANDARD 100 MM
- Manufacturer: Davis-Standard
Used temperature control panel previously used with 100mm Davis Standard extruder. No temperature instruments included. Previously used with PLC for temperature input.
Hainesport, NJ - Trusted Seller
DAVIS STANDARD 100 MM
- Manufacturer: Davis-Standard
Used temperature control panel previously used with 100mm Davis Standard extruder. No temperature instruments included. Previously used with PLC for temperature input.
Hainesport, NJ - Trusted Seller
DAVIS STANDARD DSC-U2
- Manufacturer: Davis-Standard
Used Davis Standard/Killion model DSC-U2 fly knife cutter. Will accomodate maximum 2" diameter product. Includes touch screen operator control. Mounted on caster base. Serial #17368.
Hainesport, NJ
Tip: Enter manufacturer, model or keyword