Used Ball Mills in Canada

Denver 4' x 8' Ball Mill

• Manufacturer: Denver

Drive Configuration: Electric Motor(Not Included) Close-Coupled to a Gear Reduction Unit Approx. Dimensions: Condition & Additional Notes: are one of the most precise, reliable and cost effective methods of fine ...

Mill, Ball, 9'6" X 14', Dominion, 500 HP, #D741926

• Manufacturer: Dominion

Dominion 9'6" diameter X 14' long Grinding Mill with 500 HP, 2300 Volt, 3/60Hz Synchronous motor. Shell measures 1-1/4" thick. Includes 24" diameter Wichita Pneumatic Air Clutch and 40" diameter X 24" wide self-a...

Denver 4ft Dia. x 5ft Long Ball Mill

• Manufacturer: Denver

Fabricated Scoop Feed with Feed Box Trommel Overflow Discharge Self-Aligning Babbitt Bearings Straight-Cut Bull and Pinion Gear 8in Wide Complete with Guarding Operating Speed Approx. 29 RPM Belt Drive Configurat...

New Surplus Citic 21ft Dia. x 33ft Long Ball Mill

• Manufacturer: Citic Heavy Industries

Complete Mills Diameter: 21ft (6.4m) | Length: 33ft (10m) | Discharge: Trommel Discharge | Drive: Electric Motor | Power output: 6500kW | Frequency: 50Hz

New Surplus NHI 6.4m Dia. x 10m Long Ball Mill

• Manufacturer: NHI (Northern Heavy Industries)

Complete Mills Mill diameter: 6,400mm Dia. (21ft) | Mill length: 10,000mm (32.8ft) | Mill diameter (inside liners): 6,160mm (20.2ft) | Effective grinding length: 10,000mm (32.8ft) | Shell effective volume: 298m³ ...

Denver 4 x 6 Ball Mill

• Manufacturer: Denver

Rubber Liners Straight Cut Gears Bull Gear 126 Teeth Pinion Gear 17 Teeth Mounted on Steel Operating Stand 40 HP Electric Motor 460 Volt 60 Hz. 880 RPM 55 AMP Belt Drive through Jack Shaft Final Mill Speed Approx...

36 in x 36 in Shop Built Ball Mill

Continuous flow. 2½ in. infeed. 4 in. discharge. Chain driven through a GM transmission coupled to a Radicon Size 3 reducer - Unlined shell. Mounted on 48 in. x 60 in skid.

60 Inch Ball Mill Bearing

60 Inch Ball Mill Bearing. Completely forged and machined. Housing with all oil and water journals. Plus babbitt. Shipping information: Dimensions (L x W x H): Weight: 1950 lbs.

Eimco 4 ft. x 4 ft. Ball Mill

• Manufacturer: Eimco

New Rubber Liners Installed Teco 30 HP Electric Motor 3 Phase RPM 1750 Scoop Feed Mounted on Steel Frame with Guards.

Dominion 9.5 ft x 14 ft Ball Mill

• Manufacturer: Dominion

Dominion Ball-Rod Mill. 9.5 ft. diameter x 14 ft. long. 1.25 in. thick shell. Trommel discharge screen. Herringbone bull and pinion gears. 24 in. diameter Wichita pneumatic clutch. 40 in. diameter x 24 in. wide s...

Skid Mounted 6.5 ft x 30 in Ball Mill

Skid Mounted Ball Mill. Steel lifters. Scoop feed Overflow discharge. Bull gear - spur type. Pinion gear - Spur type and belt driven. 460 Volt Motor All mounted on operating frame. Shipping information Dimensions...

7 ft x 5.5 ft Ball Mill

7 ft. diameter. 5.5 ft. long. Scoop feed. 18 in. diameter overflow discharge. Straight cut bull and pinion gear 8 in. wide Babbitt bearings. Belt driven by a 100 HP motor . 208-230/460V. 1200 rpm. 3 phase. 10 in....

4ft x 5ft Custom Built Ball Mill

• Manufacturer: Custom Built

Tire Drive Configuration Drive: 3-Phase Size: 4ft x 5ft | Feed type: Center Feed | Discharge type: Overflow | Hp/kw: 20/15 | Rotation speed: 3520 RPM | Voltage: 230/460 Volts | Current: 43.8/21.9 Amps

Howard Marten Co. Ball Mill Journal Lift and Lubrication System

• Manufacturer: Howard

High Pressure and Low Pressure Circuit Twin Grayco Fire-Ball Air-Operated Pressure Pumps (1) Low Pressure Lube Pump (50 PSI) Direct Coupled All mounted on an Approx. 130 Gallon Oil Holding Tank Complete with Oil ...

Union Ironworks 4 ft x 4.5ft Ball Mill

• Manufacturer: Union

4 ft x 4.5 ft Belt drive pinion gear. 17 teeth. 48 in. dia. pinion shaft pulley. 50 hp electric motor. 8 3/8 in. dia. motor drive pulley. Straight cut bull gear (96 teeth). Complete with scoop feed and trough. Mo...