Used process engineering

5 x 9 Ft. NEW Manufacture Ball Mill

- New manufacture 5 x 9 ball mill - Manufactured in Europe by DAI - 60 Hz electrical - Offered complete with components described below: - Cast steel heads, bearings housings, and gears NDT tested using dye-penet...

5 x 7 ft (1.5 x 2 m) Allis Chalmers Ball Mill

• Manufacturer: Allis-Chalmers

- Rebuilt, unused, and ready to ship - In excellent condition - Configured for overflow discharge wet or dry grinding with rubber liners - Mill feed and discharge heads, bull gear and pinion gear inspected and ND...

7 x 5.5 ft Ball Mill with 100 HP

- 7 x 5.5 ft grinding volume - 100 HP induction motor - Scoop feeder - Shell access door - 8" bull gear face - 18 tooth pinion gear - Straight cut gear teeth - I-beam steel skid - Babbitted trunnion bearings - Be...

10 x 14 ft (3 x 4.3 m) Marcy Ball Mill with 800 HP

- Overflow discharge - Previously NDT tested - Lincoln gear-spray lubrication system - March 650-AL trunnion bearing lubrication system - New spare bronze insert - Ring gear - Pinion - Eaton Airflex 28VC650 dual ...

8.5 x 13.5 ft Unused Outotec Ball Mills with 450 HP

• Manufacturer: Larox

- Unused Outotec Ball mills - Delivered to site, never installed or operated - 2 units available - 8.6 x 13.5 ft mill shell (3.2 x 5.6 m) - Trunnion supported ball mill - Ring and pinion gear drive - Mill drawing...

10.5 x 18.5 ft Unused Outotec Ball Mill with 1,000 HP

• Manufacturer: Larox

- Unused surplus Outotec ball mills - 2 matching units available - Delivered to site, never installed or operated - 10.5 x 18.4 ft mill shell (3.2 x 5.6 m) - Cast mill heads - Trunnion supported mill - Ring and p...

9 x 10 ft (2.75 x 3 m) Allis Chalmers ball mill with 400 HP

• Manufacturer: Allis-Chalmers

- 9 x 10 ft Allis Chalmers ball mill - Feed and discharge heads - Configured for overflow discharge and wet grinding - 2 piece bull gear with 248 teeth and 13 inch face - 20 tooth pinion with assembly - 2 lubrica...

8 x 6 ft (2.5 x 1.8 m) Hardinge conical ball mill with 200 HP

• Manufacturer: Hardinge

- 8 x 6 ft Hardinge conical ball mill on a steel skid - Wet grinding, overflow discharge - Single piece shell with access hatch - Falk gear reducer: 5.86:1 reduction ratio, 1.5 SF - Liners installed - Double heli...

9 x 12 ft. Allis Chalmers Rod or Ball Mill with 400 HP

• Manufacturer: Allis-Chalmers

9 x 12 ft. Allis Chalmers Rod or Ball Mill w/ 400 hp - Herringbone (1 piece) bull gear, 302 teeth, 20 in. face - Herringbone pinion, 30 teeth, 20 in. face - Westinghouse 400hp, 750 rpm, 575 volts - Model SR-2614 ...

Unused rubber liners for a 3.4 x 6 m Fuller ball mill

- Unused surplus neoprene rubber liners made by Metso - Designed for 3.4 x 6 m Fuller ball mill - In storage, available now - Stored in shipping container - Available as a full set only

14.5 x 28 ft (4.5 x 8.5 m) Allis Chalmers ball mill with 3,000 HP

• Manufacturer: Allis-Chalmers

- Configured for wet overflow discharge - 2 piece mill shell - Trunnions with liners - White metal trunnion bearing journals - 289 tooth two-piece bull gear - Bull gear guards - 24 tooth pinion - Falk gear reduce...

6 x 17 Ft. Marcy Ball Mills

- Used Refurbished Marcy Ball Mills - 2 Available - 17 ft. 19 in Long x 6 ft. 4 in. Width - 450 HP Weg Motor, 480 volt - Soft Start Motor System - David Brown Gearbox G17 9:1 ratio - Voith.562 EPK Clutch ...