Used Dredges in New York, USA

MUDCAT 915 DREDGE #4233

MUDCAT 915 DREDGE (Ref#4233) Detroit diesel engine, 3826 hours, secondary hour meter reading 985, boom, mud shield, enclosed cab, winch, 108" wide, auger, toolboxes (no trailer) Price on Request

BAGEMA CUTTER SUCTION DREDGE #3711

BAGEMA CUTTER SUCTION DREDGE (Ref#3711) Built 1987.18m x7.3m x 2.5m. Depth capacity 35m, max discharge length 1700m, max head dredge pump 8.5 bar, total weight: 80 ton. Cat 3408 (400HP) diesel engine powered jet ...

20" INLAND CUTTERHEAD DREDGE #3914

20" INLAND CUTTERHEAD DREDGE (Ref#3914) 55' dig depth, 70' Ladder length, 155' Length x 34' breadth x 6.75' depth, 5' operating draft, main engine EMD 16-645 (2000 hp), 200 HP hydraulic cutter, HPU Cat 3408, (2) ...

8" CUTTERHEAD SUCTION DREDGE #4041

8" CUTTERHEAD SUCTION DREDGE (Ref#4041) Built 1988, 6 x 8, 47' overall length (ladder up), 30' hull length, 11'10" beam, 4' depth, 20' ladder length, 1000 gal fuel capacity, approx. weight 47,000 lbs, 17' digging...

CRISAFULLI 6000 ROTOMITE DREDGE #4261

CRISAFULLI 6000 ROTOMITE DREDGE (Ref#4261) Built 2003, 20' max dredge depth, 102" cutterhead width, 18000 lbs, 32.5' long x 8.5' beam x 27" draft, steel pontoons, new 275 John Deere diesel engine (rebuilt 2024 wi...

ELLICOTT 970 CUTTERHEAD DREDGE #3840

• Manufacturer: Ellicott

ELLICOTT 970 CUTTERHEAD DREDGE (Ref#3840) Built 1981, currently being refurbished, wider pontoons modified, hydraulic spud carriage, 1050 hp Cat 23508 main engine (low hours on rebuild), 16" suction, 18" Ellicott...

24" CUTTERHEAD SUCTION DREDGE #3908

24" CUTTERHEAD SUCTION DREDGE (Ref#3908 ) Built 2005, reconditioned 2009 and again in 2015, modular design of all welded steel, 133' x 32' x 7' depth, 3.5' draft (hull only), 170' overall length, 24 x 24 HHD 62 G...

MUDCAT MC2000 AUGER DREDGE #3608

MUDCAT MC2000 AUGER DREDGE (Ref#3608 ) 2 available, (1) Built 2001 and (1) built 1999 with Cummins Tier 4i engines, 24" diameter auger, 20,000 lb torque, 20' depth, forward/reverse digging, currently on land, loc...

8" CUTTERHEAD BELL DREDGE PUMP #4267a

8" CUTTERHEAD BELL DREDGE PUMP (Ref#4267a) Used on one job, very good condition. (it was attached to a Cat 336 long reach excavator to dredge 50'). Price : $90,000

IMS VERSI-DREDGE MODEL 4010 #4236

IMS VERSI-DREDGE MODEL 4010 (Ref#4236 ) Built 1993, 4311 hours, 5.9L Cummins 177 hp 6 cylinder engine, 20' digging depth, 8' auger head, cable travel with windlass drive, haul trailer with pintle hitch, fittings,...

16" x 18" CUTTERHEAD DREDGE #3449

16" x 18" CUTTERHEAD DREDGE (Ref#3449) Built 2012. 102' x 23'6", hull depth 5'. Ladder length: 55'. Minimum depth: 6', max depth 44'. Center section: 36' x 11' x 5'. Side pontoons: 90' x 6' x 5'. Dredge pump: Pea...

MUD CAT 115D DREDGE #3731

• Manufacturer: Caterpillar

MUD CAT 115D DREDGE (Ref#3731) Built 2020, used very little (less than one week), 15' working depth, 8' cut width, 17" cut height, 22.5" avg draft, Catamaran hull type, John Deere 125 hp engine, 60 gal fuel capac...

MUDCAT SP915 8" AUGER DREDGE #4191

MUDCAT SP915 8" AUGER DREDGE (Ref#4191) 15' depth. 32' length. Detroit 6 cylinder. 8" discharge. Cutter head width: 98". Capacity: 2000 gallons per minute. Thomas pump. Replaced main gear box – rebuilt box $30k, ...

12" x 12" ALL ALUMINUM CUTTERHEAD DREDGE #3400

12" x 12" ALL ALUMINUM CUTTERHEAD DREDGE (Ref#3400) Built 2019, Overall length (with ladder) 46'. Hull length 30' plus 7' ladder. Overall width: 11.4'. Hull depth: 3.5'. Average draft (with fuel): 2' Aluminum uni...

8" SDR17 HDPE DREDGE PIPE #4179a

8" SDR17 HDPE DREDGE PIPE (Ref#4179a) 3,900' available, 40-50' sections, located Florida Price : $8 per foot 10" SDR17 HDPE DREDGE PIPE (Ref#4179b ) 750' available, 40-50' sections, located Florida Price: $12 per...