Used variable speed in Alberta, Canada

1981 John Deere Turbo 8820 Combine

• Manufacturer: John Deere

John Deere 214 14 ft pick-up header, variable speed reel, chopper/straw spreader, 16 ft auger, 24.5-32 front tires, 11.25-24 rear tires

1984 Massey Ferguson 885 30 Ft Swather

• Manufacturer: Massey Ferguson
• Model: 885
• Horsepower: 158 horsepower
• Cutting width: 4.88 meter

center delivery rigid draper header, batt reel, variable speed reel, fore & aft, 6 cylinder diesel engine, 18.4-16.1 front tires, 8.5-14 rear tires

1997 John Deere 9600 Combine

• Manufacturer: John Deere
• Model: 9600
• Horsepower: 260 horsepower
• Grain tank size: 8,457.376799999998 liter

1998 John Deere 914 14 ft pick-up header, variable speed reel, fore & aft, reverser, rock trap, chaff spreader, fine cut chopper/spreader, grain tank extensions, 18 ft auger, A/C, buddy seat, 30.5-32 front tires,...

2014 VERNER MODEL VD-12000 TILT WELDING POSITIONER

• Manufacturer: VERNER

2014 VERNER MODEL VD-12000 TILT WELDING POSITIONER MANUFACTURER: VERNER MODEL: VD-12000 SERIAL NO.: X1200011 MFG DATE: MARCH 2014 POWER: 220V 60HZ 3PH Type: Tilt Positioner Table Size: 59'' table Load Cap...

2009 Case 7088 Combine

2011 Case iH 2016-14 14 ft pick-up header, variable speed reel, auto header height, fore & aft, reverser, lateral tilt, rock trap, yield & moisture, chaff spreader, chopper, grain tank extensions, 20 ft auger, A/...

4KVS – Manual Milling machine Single Phase

• Manufacturer: LINMAC

Specifications and standard Features: 5Hp 3Ph 575V CSA approved electrics Table size 10” x 54” NT40 Taper spindle Variable speed Hardened & Ground 3 axis X- axis dove tail Y/Z axis square slideway Coolant...

X6323A 9 x 49 Milling machine

• Manufacturer: Ficom

SPECIFICATIONS: - TABLE 9″ X 49″ - SPINDLE R-8 - MOTOR 3 HP - ELECTRICS 220/60/1 PHASE - INFINITELY VARIABLE SPEED 70 – 4200 RPM - LONGITUDINAL TRAVEL 31″ - VERTICAL TRAVEL 16″ - CROSS TRAVEL 13″ - QUILL TRAVEL ...

2008 HYD-MECH S-20A SERIES II

• Manufacturer: Hyd-Mech
• Model: S20A

HYD_MECH S-20A Series II Equipped With Equipped with (subject to buyer verification): Carbide guides 500PSI Hydraulic system 7 US Gallons Hydraulic Tank Capacity 6 US Gallons Coolant Tank Hydraulic Vise Control ...

PBM-GEVS500A Milling Machine

• Manufacturer: LINMAC

SPECIFICATIONS: TRAVEL · Longitudinal travel – X manual 1120 mm · Cross travel – Y manual 380 mm · Vertical travel – Z manual 450 mm · Longitudinal travel – X Auto 920 mm · Cross travel – Y Auto 500 mm · V...

857II Manual Milling Machine

• Manufacturer: LINMAC

Description: 5HP 3PH Motor CSA Elec. Control Panel Spindle: ISO#40, Quill: 105mm Dia. Variable Speed: 60-3600RPM TABLE: 12”x54” X/Y/Z AXES TRAVEL: 36”X16”X16” Rapid Traverse motor for Z-axis Chip Tray Co...