Used nip roll in igirisu

24" X 10" FARREL 4-ROLL "INVERTED L" RUBBER CALENDER ROLLING MILL WITH PAYOFF

• Manufacturer: Farrel

419-269-2000 870 Curtis Street Toledo, OH 43609 Machine Information 24" X 10" FARREL 4-ROLL "INVERTED L" RUBBER CALENDER ROLLING MILL WITH PAYOFF: STOCK #17226 Stock #: 17226

Pull Roll Stand

steel bottom rolls with rubber nip, US Varidyne 1 hp motor 800-2180 rpm, PIV, stop/start, emergency stop, yarn guides. Pull Roll Stand (3) 18" wide x 6" diameter rolls

Nip Stand - 64" rolls

good condition. UNKNOWN Nip Stand - 64" rolls needs cleaning but reported in .

High Precision Calendering Machine for Prismatic Cell Production Line

• Manufacturer: TMAXCN

High Precision Calendering Machine for Prismatic Cell Production Line 1、List of equipment specifications 1.1 Equipment composition and function Main configuration of equipment 2、Introduction to equipment principl...

Padder / Nip

No stand. Some surface rust on rolls but should clean up easily. Last used as pull rolls. No motor but could be supplied at additional cost. UNKNOWN Padder / Nip 28" x 6" diameter steel rolls.

Saturator Padder

nip rolls, idler roll top & bottom, adjustable nip, (2) bottom slotted liquid dispensers between roll, no dip pans, only (1) unit with adjustable side dams, 5 hp Reliance DC motor, no control panels. Rolls appear...

Laminating Line Components

- Laminating Nip Stand, 30" wide. (1) 15.5" diameter chrome hot/cold roll. (2) 6.5" diameter rubber nip rolls mounted above and to the side of main chrome roll with manual pressure adjustment. (1) 11.5" diameter ...

CUSTOM R&D Coating Line

- Coater with 16" wide rolls, (1) 6" diameter top chrome roll, (1) 8" dia bottom roll, (1) 8" diameter rubber over steel nip roll, pond feed / flooded nip, micro-adjustment for knife, pneumatic controls for coati...

CUSTOM Slitter Rewinder with Inspection

includes stationary jack-stand let-off, 126" face lighted viewing board with pneumatic nip-hold down, operator controls and operator platform, 2- roll take-up 126" roll face x 11" diameter with 1-1/2" spacing bet...

STERLING Lab Extrusion Coater Laminator

• Manufacturer: Sterling

equipped with 30" diameter Pinnacle single position unwind with roll lift, laminator (20" face x 20" diameter chill roll, 6" diameter rubber-covered nip roll, 8" diameter backup roll), Sterlco unit to heat or chi...

WAYNE 1" 30:1 Floor Model Vented

• Manufacturer: Wayne

- Motor With Belt Drive, Controlled With WEG Vector Duty Drive, 4 Barrel Zones, - Air Cooled, 6 Die Zones, With Melt Temp, Extruder RPM, And Motor Load, Has - Gefran Pressure Transducer With Readout, Includes Scr...

2004 MENZEL Coater

• Manufacturer: Menzel

The coater is dip and nip (between 2 rolls to squeeze coating) with agitators in the bottom of the pan. Has electric infrared heaters used to flash off the water. Infrared heaters are 86,400 watts and 294,624 BTU...

BOULIGNY / PRODEX / LEESONA PP Tape Line:

Conair 4 station dosing, PLC controlled. AEC OS-014 Blender. Foremost Grinder for inline reprocessing. Cramer feeder. Prodex 3.5" Extruder, 25:1 L/D. Lufkin TMF35 gearbox, 125 hp Baldor DC motor with Bardac drive...