Used nip roll in USA

Amut PET,PP & PS ; 1000mm sheet extrusion line. 75mm extruder, eti#33.000

• Manufacturer: Amut

1000mm Amut PET,PP & PS sheet extrusion line. 75mm extruder, gear pump. 1000mm die. 1000mm 3 roll stack, haul off Accumulator and winder. 2016 * 3 component gravimetric dosing unit. * 75mm extruder Model EA75. ve...

Battenfeld PET sheet line with Dryer. 1200mm wide eti#33.000

• Manufacturer: Battenfeld

1200mm Wide Battenfeld Gloenco PET Sheet Line VERY COMPLETE LINE WITH: IRD crystalizer Dryer, 120mm Extruder, Gneuss Screen Changer, Gear Pump, 1400mm Die, Roll Stack, Haul Off Winder. * 3200 litre Container mode...

Leistritz Lab Sheet Line, Model ZSE27 MAXX-40D

• Manufacturer: Leistritz

Used-Leistritz Lab Sheet Line, Includes the following: Leistritz Extruder  Model ZSE27 MAXX-40D. 29.8 Kw Main Drive, 1200 rpm Screw Speed. 320 Hours. (4) Schenck Feeders. (2) AEC Chilling Units. (1) Sterlco Unit....

NIP ROLLS

2" dia x 5" long shafts with bearing housing. NIP ROLLS 9" dia x 72" face rubber rolls.

Nip Rolls

with side frames with sprocket but NO base available. Nip Rolls (2) 18" x 6.6" diameter rolls rubber over stainless

Nip Rolls

10-1/8" tapered shafts. 1st taper (closest to rubber) - 4" diameter 2nd taper - end of shaft, 2.5" diameter. Nip Rolls 6-1/2" dia x 76" face NEW.

Nip Roll Assemblies

controls, CMC Pacemaster 4 speed controls. Last used in R&D extrusion operation. Optional components available at additional cost include creel, water bath, steam oven, winder. Nip Roll Assemblies 2"W x 4" dia pn...

Rubber Nip Rolls

4.5" dia shafts, 78" overall length. Previous use in scouring operation. Rubber Nip Rolls 13" diameter x 50" working width

SYCODAL CCE-CEC-LR NIP ROLL CONTROL BOARD 3 PHASE 380V

• Manufacturer: SYCODAL

“SURPLUS INVENTORY FROM A MANUFACTURING FACILITY COMES ONLY WITH WHAT IS PICTURED”

RUBBER Nip Roll for Draw Stand

Two tier shaft. 1st tier (closest to hub) 8-3/4"L x 2.5" diameter. 2nd tier 17"L x 1.5" diameter. Appears reconditioned and in VG condition. RUBBER Nip Roll for Draw Stand 29" f ace x 9-3/4" diameter.

Laminating Nip Stand

(1) 15.5" diameter chrome hot/cold roll. (2) 6.5" diameter rubber nip rolls mounted above and to the side of main chrome roll with manual pressure adjustment. (1) 11.5" diameter bottom roll with pneumatic pressur...

LYONS Nip Assembly

manual screw pressure, let-off roll, bow roll, overall footprint 8' x 11' 3" x 6' high. Dove tail bar for mounting slitter heads but heads are not available. Previously had an explosion proof motor. Last used in ...

24" X 10" FARREL 4-ROLL "INVERTED L" RUBBER CALENDER ROLLING MILL WITH PAYOFF

• Manufacturer: Farrel

419-269-2000 870 Curtis Street Toledo, OH 43609 Machine Information 24" X 10" FARREL 4-ROLL "INVERTED L" RUBBER CALENDER ROLLING MILL WITH PAYOFF: STOCK #17226 Stock #: 17226

Nip Stand - 64" rolls

good condition. UNKNOWN Nip Stand - 64" rolls needs cleaning but reported in .

Padder / Nip

No stand. Some surface rust on rolls but should clean up easily. Last used as pull rolls. No motor but could be supplied at additional cost. UNKNOWN Padder / Nip 28" x 6" diameter steel rolls.